Custom Anchors and Masonry Accessories
For attaching brick veneer to concrete backup walls with #100 dovetail anchor slot.
Pos-I-Tie® Anchoring Systems
The Original Pos-I-Tie® is a two-piece system for attaching brick and stone veneer to various existing backups. It simultaneously penetrates the exterior insulation, makes positive contact with the backup for transfer of lateral loads, and seals the hole in the insulation with an EPDM washer under the barrel head. Introduced in 1985, The Pos-I-Tie® was the first barrel screw in the industry and has been successfully anchoring veneers for 35 years.
Standard sizes for sheathing thicknesses of 5/8", 1", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4" and 4-1/2".
Custom lengths beyond 4-1/2" are available.
Pos-I-Tie® 3/16" diameter Wire Triangle Ties available standard in lengths of 3", 3-1/2", 4" and 5" in hot-dip galvanized and stainless steel. Custom wire tie lengths are available.
The Pos-I-Tie® ThermalClip® is designed for use with the Original Pos-I-Tie® Veneer Anchoring System. This new breakthrough in masonry construction adds thermal-break technology to all the advantages of the Original Pos-I-Tie® Veneer Anchoring System. It has passed NFPA 285 Testing as part of the CavityComplete® Wall system.
The clip snaps into the Pos-I-Tie® barrel loop creating a thermal break between the wire tie and the barrel. This break also allows for stainless wire ties to be used with the Zamak barrel screw.
Use #282-N Pintle Wire Ties with the ThermalClip®
Chuck Adapter for installation of the barrel screws. Use a drill with a depth sensitive nose piece or a variable clutch
adjustment. The barrel end of the Pos-I-Tie® is placed into the reusable chuck adapter.
For steel studs, drill the Pos-I-Tie® through the exterior insulation and into the metal stud. Use a drill with 1500 - 2000 RPM. Do not over-torque!
Sleeve Tool - Allows for drilling hole through up to 2-1/2" insulation and using the same sleeve tool for placement of the Chuck Adapter so you can use one drill for both operations. Pre-drill a 3/16" (4.76 mm) hole to a depth of 2" (51
mm). Slide the Sleeve tool over the drill bit and insert the CMU/Concrete Screw into the chuck adapter. Torque screw
into the pre-drilled hole.
The Chuck Adapter and Sleeve Tool are sold separately.
The Pos-I-Tie® ThermalClip® is designed for use with the Original Pos-I-Tie® Veneer Anchoring System. This new breakthrough in masonry construction adds thermal-break technology to all the advantages of the Original Pos-I-Tie® Veneer Anchoring System. It has passed NFPA 285 Testing as part of the CavityComplete® Wall system.
The clip snaps into the Pos-I-Tie® barrel loop creating a thermal break between the wire tie and the barrel. This break also allows for stainless wire ties to be used with the Zamak barrel screw.
Use #282-N Pintle Wire Ties with the ThermalClip®
3/16" diameter looped wire ties designed for the Original Pos-I-Tie® Barrel Screws. Loop allows for 1-1/4" vertical adjustment above and below the plane of the barrel screw.
Standard lengths: 3", 3-1/2", 4" and 5"
Available in hot-dip galvanized and stainless steel
Special lengths are available.
The Pos-I-Tie. KeyBolt is designed for easy and effective stone anchor attachment where sheathing/insulation is installed over the backup wall. The KeyBolt system penetrates the sheathing, drills into the backup, and seals the hole to avoid water/air penetration. All compression loads are transferred to the backup through the KeyBolt without damaging the sheathing. When ordering, specify the type of stone anchor with the “KeyBolt Slot".
KeyBolt Barrel Components
Pos-I-Tie. KeyBolt barrel (including 2 hex nuts and EPDM washer
Barrel screw (self-drilling screw, concrete screw, or structural steel screw)
Anchor with KeyBolt Slot
Made To Order
For use with the Pos-I-Tie® ThermalClip® anchoring system.
1/8" or 3/16" thick stainless steel 2" wide.
Specify anchor length and split bend length.
(Note! Anchor length starts 3/4" out from the backup wall. See submittal sheet for details.)
Made To Order
For use with the Pos-I-Tie® ThermalClip® anchoring system.
1/8" or 3/16" thick stainless steel 2" wide.
Specify anchor length and bend length.
(Note! Anchor length starts 3/4" out from the backup wall. See submittal sheet for details.)
Made To Order
For use with the Pos-I-Tie® ThermalClip® anchoring system.
1/8" or 3/16" thick stainless steel 2" wide.
Specify anchor length and bend length.
(Note! Anchor length starts 3/4" out from the backup wall. See submittal sheet for details.)
Made To Order
For use with the Pos-I-Tie® ThermalClip® anchoring system.
1/8" or 3/16" thick stainless steel 2" wide.
Specify anchor length, pin diameter and length and center of pin to end of anchor. Pin can be loose or welded.
(Note! Anchor length starts 3/4" out from the backup wall. See submittal sheet for details.)
Made To Order
Used to anchor stone with the Heckmann #75-KB Pos-I-Tie® Keybolt Anchoring System. The Keybolt Barrel Screw installs through insulation into the backup and the hole is sealed with a tightened nut and washer. The anchor is installed between the two nuts and aligned with the stone. The outer nut is tightened to secure the anchor.
Specify thickness of anchor, length, width (Minimum 1.25"), Bend with KeySlot (minimum 2.25") and split-bend lengths.
Type 304 or Type 316 Stainless Steel Only.
(For same anchor with a hole instead of the KeySlot see #274 Screw-On Split-Bend Stone Anchor.
Made to Order
Used to anchor stone with the Heckmann #75-KB Pos-I-Tie® Keybolt Anchoring System. The Keybolt Barrel Screw installs through insulation into the backup and the hole is sealed with a tightened nut and washer. The anchor is installed between the two nuts and aligned with the stone. The outer nut is tightened to secure the anchor.
Specify thickness of anchor, length, width (Minimum 1.25"), Bend with KeySlot (minimum 2.25") and bend length.
Type 304 or Type 316 Stainless Steel Only.
(For same anchor with a hole instead of the KeySlot see #275-Z Screw-On Z-Type Stone Anchor.
Made to Order
Used to anchor stone with the Heckmann #75-KB Pos-I-Tie® Keybolt Anchoring System. The Keybolt Barrel Screw installs through insulation into the backup and the hole is sealed with a tightened nut and washer. The anchor is installed between the two nuts and aligned with the stone. The outer nut is tightened to secure the anchor.
Specify thickness of anchor, length, width (Minimum 1.25"), Bend with KeySlot (minimum 2.25") and bend length.
Type 304 and Type 316 Stainless Steel Only.
(For same anchor with a hole instead of the KeySlot see #275-U Screw-On U-Type Stone Anchor.
Made to Order
Used to anchor stone with the Heckmann Pos-I-Tie® Keybolt anchoring system. The Keybolt Barrel Screw installs through insulation in the backup and the hole is sealed with a tightened nut and washer. The anchor is installed between the two nuts and aligned with the stone. The outer nut is tightened to secure the anchor.
Specify thickness of anchor, length, width (Minimum 1.25"), Bend with KeySlot (minimum 2.25"), diameter and length of pin and location of pin. Specify if pin is to be loose or welded in place.
Type 304 or Type 316 Stainless Steel Only
(For same anchor with a hole instead of the KeySlot see #276 Screw-On Pin-Type Stone Anchor
Made to Order
Used to anchor stone with the Heckmann #75-KB Pos-I-Tie® Keybolt Anchoring System. The Keybolt Barrel Screw installs through insulation into the backup and the hole is sealed with a tightened nut and washer. The anchor is installed between the two nuts and aligned with the stone. The outer nut is tightened to secure the anchor.
Specify thickness of anchor, length, width (Minimum 1.25"), bend with KeySlot (minimum 2.25") and welded plate height.
Type 304 and Type 316 Stainless Steel Only.
(For same anchor with a hole instead of the KeySlot see #278 Welded Plate Strap Stone Anchor.
Pintle Wire Tie for use with the Pos-I-Tie® ThermalClip® system.
3/16" diameter wire only – Fits in ThermalClip® and allows 1 ¼" vertical adjustment above and below the plane of the ThermalClip®
Standard Lengths: 3", 3-1/2", 4" and 5"
Available in Stainless Steel and Hot Dip Galvanized
Custom lengths are available.
Thermal-Grip® washers are designed for use with the Pos-I-Tie® Veneer Anchoring System. Prongs enable pre-spotting into rigid insulation for fast on-the-wall fastener assembly. The ThermalGrip® washer allows the masonry tie to also act as a Continuous Insulation fastener to prevent wind blow-off during construction.
The Large Steel EPDM washers are designed for use with the Pos-I-Tie® Barrel Screws. The washer allows the masonry tie to also act as a Continuous Insulation fastener to prevent wind blow-off during construction. This is a 1-1/2" diameter steel backed EPDM washer.
The 75-PW 2" diameter plastic washer was designed for the Pos-I-Tie® Veneer Anchoring System. The washer slides onto the Pos-I-Tie® barrel screw and allows the masonry tie to also act as a Continuous Insulation fastener to prevent wind blow-off during construction.
Masonry to Masonry Anchors
The Original Pos-I-Tie® is a two-piece system for attaching brick and stone veneer to various existing backups. It simultaneously penetrates the exterior insulation, makes positive contact with the backup for transfer of lateral loads, and seals the hole in the insulation with an EPDM washer under the barrel head. Introduced in 1985, The Pos-I-Tie® was the first barrel screw in the industry and has been successfully anchoring veneers for 35 years.
Standard sizes for sheathing thicknesses of 5/8", 1", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4" and 4-1/2".
Custom lengths beyond 4-1/2" are available.
Pos-I-Tie® 3/16" diameter Wire Triangle Ties available standard in lengths of 3", 3-1/2", 4" and 5" in hot-dip galvanized and stainless steel. Custom wire tie lengths are available.
One-piece, non-adjustable anchors used for attaching brick veneer to an existing concrete wall which contains Standard 1" deep x 1" wide dovetail slot with a 5/8" throat at the face of concrete.
Can also be used with Wood or CMU backup as a single anchor fastened to the backup for brick veneer without exterior insulation in the cavity.
Screw On Channel slots have two tabs that allow attachment to the backup with screws or expansion anchors. These tabs are level with the backup wall. They are typically attached to existing backup walls of wood, concrete, brick or CMU. Various channel slot anchors
This non-adjustable wire wall tie is used to bond masonry veneer to a masonry back-up wall, or to bond two masonry walls. The TMS402 Masonry Building Code no longer allows drips on anchors.
Standard: 3/16" diameter with 2" bends in lengths of 6", 8", 10" and 12".
Hot dip galvanized and Stainless Steel.
Special sizes are available.
This non-adjustable wire wall tie is used to bond masonry veneer to a masonry back-up wall, or to bond two masonry walls. The TMS402 Masonry Building Code no longer allows drips on anchors.
Standard: 3/16" diameter Width: 2" and 4"
Length: 6", 8", 10" and 12"
Hot dip galvanized and Stainless Steel.
Specials are available.
Used to secure a masonry veneer to a masonry backup wall. The #262 Double Eye Rod anchor is embedded in the backup CMU and has two eyelets for the #263 Pintle Wire Tie.
Available in Stainless Steel or Hotdip Galvanized
Used to secure a masonry veneer to a masonry backup wall with #262 Double Eye Rod, #213 Double Pintle Brick Veneer Anchor or #1300 Pintle/Eye Wire reinforcement.
Used as a tie between intersecting masonry walls. 1/2" sq 16 ga wire mesh Hot dip Galvanized.
Standard: 4" x 8"
One size only.
Used as a 2-piece adjustable anchor for attaching brick veneer to a solid backup wall or one with Gypsum Sheathing or Plywood. This is not for use with polyiso insulation or mineral wool.
12 or 14 gage thick x 1-1/4" wide x 5-1/2" long with 5/16" holes
Available Type 304 Stainless Steel and Hotdip Galvanized
Use with #316 Triangle Wire Ties
The #316 Triangle Wire Tie is used for attaching brick veneers to backup systems that require an adjustable anchoring system. The wire triangle is hooked onto one of various backup anchors and is then embedded in the veneer wall mortar joint.
3/16" Diameter in lengths of: 3", 4", 5", 6", 7" and 9"
Available in Type 304 Stainless Steel and Hot Dip Galvanized
Made to Order
Angle Clip for various attachments.
#341: Specify thickness, length, width, bend length, hole size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order
Angle Clip for various attachments.
#341-A: Specify thickness, length, width, bend length, hole sizes and locations and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 Firewall (1/8" and 16 gauge only)
Made to Order
Angle Clip for various attachments.
#341-B: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342-A: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342: Specify thickness, length, width, bend length, slot size and location and steel type.
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342-B: Specify thickness, length, width, bend length, slot sizes and locations and steel type.
Control Joint Anchors are designed to transfer loads across control joints. They are also intended to handle compression loads and control lateral movement.
22 gauge x 1-1/2" wide x 10" overall length.
Available
Stainless Steel / Plastic
Type 304 all Stainless Steel
Mill Galvanized
Cross wires spaced 16" o.c. to allow block cores to be open for vertical rebar.
Available in
Standard: 9 gauge side and cross rods
Heavy Duty: 9 gauge cross rods and 3/16" side rods
Extra Heavy Duty: 3/16" side and cross rods
For CMU walls: 4", 6", 8", 10" and 12"
Corners and Tee's are available.
Available in Stainless Steel, Hot-dip Galvanized and Mill Galvanized
Diagonal cross wires spaced 16" o.c.
Available in
Standard: 9 gauge side and cross rods
Heavy Duty: 9 gauge cross rods and 3/16" side rods
Extra Heavy Duty: 3/16" side and cross rods
For CMU walls: 4", 6", 8", 10" and 12"
Available in Stainless Steel, Hot-dip Galvanized and Mill Galvanized
Pintle wire eyes are spaced 16" o.c. and conform to TMS 402 Building Code. Cross wires are 16" o.c. Specify insulation thickness for length of the pintle eyes as well as length of #263 pintles into veneers. (Standard Pintle lengths are 3-1/4", 4-1/4" and 5-1/4".
Available in
Standard: 9 gauge side and cross rods
Heavy Duty: 9 gauge cross rods and 3/16" side rods
Extra Heavy Duty: 3/16" side and cross rods
For CMU walls: 4", 6", 8", 10" and 12"
Corners and Tee's are available.
Available in Stainless Steel, Hot-dip Galvanized and Mill Galvanized
Masonry to Structural Steel Anchors
Used for attaching masonry/veneers or block to an existing backup wall with attached Channel Slots. The 12 gauge clip is attached to 3/16" diameter wire triangle ties in lengths of 3", 4", 5", 6", 7" and 9".
Available in Stainless Steel and Hotdip Galvanized
Channel slots are welded to structural columns for adjustable attachment of masonry/veneer walls or can be attached to CMU and concrete walls using fasteners through the two holes at the top and bottom of the slot. They can also be used to replace dovetail anchor systems for concrete walls that were not cast with dovetail slots. Use with Channel Slot Anchors.
Channel slots are attached to structural columns, brick, CMU or concrete walls. Various channel slot anchors are available for veneer attachment. They can also be used to replace dovetail anchor systems for concrete walls that were not cast with dovetail slots. Use with Channel Anchors.
Available in Stainless Steel
Used for attaching brick veneer to an existing backup wall which has Channel Slots attached.
Available Thickness: 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge
Stainless Steel
Specify thickness, length from face of channel. Width is 1-1/4".
Used to attach CMU walls to structural steel beams
Order in pairs, one left and one right side anchor
Standard size: 7" L x 2" W, 1/8" thick with a 1-1/2" L-shaped bend
Standard Notch: 5/8" W x 1" D, begins 1" from end of anchor
Available in Stainless Steel and Zinc Alloy 710 Firewall (1/8" only)
Made to Order
Used to tie masonry walls to horizontal steel columns. If an airspace exists between the column and the wall, the strap should be welded to the column to prevent movement from compression.
Available in 1/8", 12 gauge and 14 gauge in Stainless Steel, and Zinc Alloy 710 (1/8" only). Specify length, width and bend length
Made to Order
Used to tie masonry walls to horizontal steel columns. If an airspace exists between the column and the wall, the strap should be welded to the column to prevent movement from compression.
Available in 1/8", 12 gauge and 14 gauge in Stainless Steel, and Zinc Alloy 710 (1/8" only). Specify length, width and bend length.
Made to Order
Used to anchor masonry walls to structural columns where the column flanges are perpendicular to the masonry wall.
3/16", 1/8" or 12 gauge.
Typical width is 1-1/4" with a 1-1/2" bend.
Specify Overall Length, length from hook to start of twist and steel type.
Available in Type 304 and Type 316 Stainless Steel, and Zinc Alloy 710 (1/8" only).
The Corrugated Column Anchor is used to anchor masonry walls to structural steel beams where the column flanges are parallel to the masonry wall. 1" deep x 5/8" wide notch fits into steel beam for secure application. Order by piece. Anchors are reversible for left or right side use.
Made to Order.
Used to anchor masonry walls to structural columns where the column flanges are perpendicular to the masonry wall on a horizontal beam.
1/8" thick - specify width, overall length and length of corrugation.
Available in Stainless Steel, Zinc Alloy 710 Firewall material and Plain Steel
Hook opening is 3/4" id x 1-1/4" long
Made to Order.
Used to anchor masonry walls to structural columns where the column flanges are perpendicular to the masonry wall on a horizontal beam.
1/8" thick - specify width, overall length length from hook to start of twist and steel type.
Hook opening is 3/4" id x 1-1/4" long
Available in Type 304 and Type 316 Stainless Steel, and Zinc Alloy 710 Firewall material
Made to Order
Used to anchor masonry walls to structural columns. Welded to structural steel beams, typically in the web of a horizontal beam.
Available 1/8" or 14 gauge - 7" high
Specify bend length welded to beam, bend length out from beam, center of slot to end and steel type.
Slot is 1/4" x 5"
Available in Plain Steel
The Weld-On Anchor rod is used to attach masonry to structural steel. The rods are welded to structural columns for attachment of masonry/veneer walls. Use #316 Triangular Wire Ties or #318 Web Ties for attachment into masonry.
1/4" diameter in 5" or 9" lengths
3/8" offset
4" of vertical adjustment with 9" length
2" of vertical adjustment with 5" length
Available in Plain Steel
The #316 Triangle Wire Tie is used for attaching brick veneers to backup systems that require an adjustable anchoring system. The wire triangle is hooked onto one of various backup anchors and is then embedded in the veneer wall mortar joint.
3/16" Diameter in lengths of: 3", 4", 5", 6", 7" and 9"
Available in Type 304 Stainless Steel and Hot Dip Galvanized
Newly Revised! Now available in 46" lengths boxed in 50 pc cartons for easy shipment.
Continuous weld-on rods are welded to steel beams for anchoring CMU or veneers to the beam using #316 Triangle Ties or #318 Web Ties.
1/4" diameter plain steel. 7 offsets each with 4" of vertical adjustment.
Made to Order
Angle Clip for various attachments.
#341: Specify thickness, length, width, bend length, hole size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order
Angle Clip for various attachments.
#341-A: Specify thickness, length, width, bend length, hole sizes and locations and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 Firewall (1/8" and 16 gauge only)
Made to Order
Angle Clip for various attachments.
#341-B: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342-A: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342: Specify thickness, length, width, bend length, slot size and location and steel type.
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342-B: Specify thickness, length, width, bend length, slot sizes and locations and steel type.
Made to Order
Efficiently transfers horizontal forces between a masonry wall and the building frame. The Twist-On Anchor allows you to connect a masonry wall to a Joist, Joist Girder or any other Truss as well as to a Castellated or Rolled Beam while allowing free deflection.
3-1/4" wide. Specify anchor length, vertical sliding bar dimension (1/2", 3/4" or 1") and steel type. Vertical Rod can be round or square.
Stainless Steel available in 3/16" or 1/8" thickness.
Zinc Alloy 710 Firewall available in 1/8" only.
Masonry to Wood
Used to anchor wood joists to a masonry wall. Bend is grouted into the CMU wall and the strap is nailed to the floor joists.
Standard: 1/8" x 1" wide Mill Galvanized.
17" long
7/32" holes spaced 3" o.c. starting 1" from end
Bend is 2"
Twist starts 11-1/2" from end
NEW STYLE REPLACING THE JOIST PIN ANCHOR
Used to anchor wood joists to a masonry wall. Bend is grouted into the CMU wall and the strap is nailed to the floor joists.
Standard: 12 gauge x 1" wide Mill Galvanized with a 2" bend grouted into the CMU.
17" long with three holes
Holes spaced 3" o.c. starting 1" from end
Made to Order
Angle Clip for various attachments.
340-B: Specify thickness, length, width, bend length, slot size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order - (See Product 187 for standard sizes)
Angle Clip for various attachments.
340-A: Specify thickness, length, width, bend length, hole size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (up to 1/8"), Zinc Alloy 710 Firewall (1/8" and 16 gauge only)
(max 1/8"), Plain Steel and Zinc Alloy 710 Firewall (1/8" and 16 gauge only)
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool
#340: Specify thickness, length, width, bend length and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (up to 1/8"), Zinc Alloy 710 Firewall (1/8" and 16 gauge only)
The #316 Triangle Wire Tie is used for attaching brick veneers to backup systems that require an adjustable anchoring system. The wire triangle is hooked onto one of various backup anchors and is then embedded in the veneer wall mortar joint.
3/16" Diameter in lengths of: 3", 4", 5", 6", 7
Available in Type 304 Stainless Steel and Hot Dip Galvanized
Used as a 2-piece adjustable anchor for attaching brick veneer to a solid backup wall or one with Gypsum Sheathing or Plywood. This is not for use with polyiso insulation or mineral wool.
12 or 14 gage thick x 1-1/4" wide x 5-1/2" long with 5/16" holes
Available Type 304 Stainless Steel and Hotdip Galvanized
Use with #316 Triangle Wire Ties
Used to bond masonry veneer to a wood frame backup wall. These are permitted only on wood backup walls. Note: TMS402 Building Code allows corrugated wall ties in walls with a maximum airspace of 1". For larger airspaces, use the #187 Corrugated Brick Veneer Anchor with Hole.
Used for attaching brick veneer to Wood backups.
Standard: 16 gauge x 1-1/4"wide with a 1-1/2" bend with a centered 5/16" diameter hole.
Steel Types: Type 304 Stainless Steel, Hotdip Galvanized after fabrication or Zinc Alloy 710 (1/8" thick only) for Firewalls.
Standard Lengths: 3-1/2" and 5-1/2"
For Custom Sizes see #340-A Corrugated L-Anchor with Hole
Screw On Channel slots have two tabs that allow attachment to the backup with screws or expansion anchors. These tabs are level with the backup wall. They are typically attached to existing backup walls of wood, concrete, brick or CMU. Various channel slot anchors
One-piece, non-adjustable anchors used for attaching brick veneer to an existing concrete wall which contains Standard 1" deep x 1" wide dovetail slot with a 5/8" throat at the face of concrete.
Can also be used with Wood or CMU backup as a single anchor fastened to the backup for brick veneer without exterior insulation in the cavity.
The Original Pos-I-Tie® is a two-piece system for attaching brick and stone veneer to various existing backups. It simultaneously penetrates the exterior insulation, makes positive contact with the backup for transfer of lateral loads, and seals the hole in the insulation with an EPDM washer under the barrel head. Introduced in 1985, The Pos-I-Tie® was the first barrel screw in the industry and has been successfully anchoring veneers for 35 years.
Standard sizes for sheathing thicknesses of 5/8", 1", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4" and 4-1/2".
Custom lengths beyond 4-1/2" are available.
Pos-I-Tie® 3/16" diameter Wire Triangle Ties available standard in lengths of 3", 3-1/2", 4" and 5" in hot-dip galvanized and stainless steel. Custom wire tie lengths are available.
Masonry to Steel Stud
The Original Pos-I-Tie® is a two-piece system for attaching brick and stone veneer to various existing backups. It simultaneously penetrates the exterior insulation, makes positive contact with the backup for transfer of lateral loads, and seals the hole in the insulation with an EPDM washer under the barrel head. Introduced in 1985, The Pos-I-Tie® was the first barrel screw in the industry and has been successfully anchoring veneers for 35 years.
Standard sizes for sheathing thicknesses of 5/8", 1", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4" and 4-1/2".
Custom lengths beyond 4-1/2" are available.
Pos-I-Tie® 3/16" diameter Wire Triangle Ties available standard in lengths of 3", 3-1/2", 4" and 5" in hot-dip galvanized and stainless steel. Custom wire tie lengths are available.
#213 Double Pintle Plate Veneer Anchors are attached directly to the backup system. Insulation/mineral wool is then placed above and below the horizontal tab. Use with #263 Double Pintle Wire Tie.
#213 Plate Tab Sizes: no insulation, 1", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4"
#263 Wire Pintles 3/16" dia Lengths: 3-1/4", 4-1/4", 5-1/4"
Available in Hotdip Galvanized After Fabrication and Type 304 Stainless Steel
NOTE - THE 282 HAS BEEN CHANGED TO NUMBER 263
Used for attaching veneer anchors to steel studs. The EPDM washer under the head seals the drilled hole. Self-drilling - no pilot hole required.
Two Sizes
TEK1012 - #10-16 x 1 1/2" Zinc Polymer coated with EPDM Washer
TEK1230 - #12 x 3 Zinc Polymer coated with EPDM washer
Masonry to Concrete or ICF Backup Walls
The Original Pos-I-Tie® is a two-piece system for attaching brick and stone veneer to various existing backups. It simultaneously penetrates the exterior insulation, makes positive contact with the backup for transfer of lateral loads, and seals the hole in the insulation with an EPDM washer under the barrel head. Introduced in 1985, The Pos-I-Tie® was the first barrel screw in the industry and has been successfully anchoring veneers for 35 years.
Standard sizes for sheathing thicknesses of 5/8", 1", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4" and 4-1/2".
Custom lengths beyond 4-1/2" are available.
Pos-I-Tie® 3/16" diameter Wire Triangle Ties available standard in lengths of 3", 3-1/2", 4" and 5" in hot-dip galvanized and stainless steel. Custom wire tie lengths are available.
Used for attaching brick veneer or stone to a concrete backup wall. The dovetail slot is nailed to the inside of the form. When the concrete is poured and the form is removed, the slot allows anchors to be installed and adjusted vertically.
Standard Size: 1" x 1" narrowing down to a 5/8" throat in 10 foot lengths. The slot is filled with flexible foam filler to prevent concrete from entering the slot during the pour.
Available in 16 and 22 gauge in Type 304 Stainless Steel and 16 gauge in Hotdip Galvanized After Fabrication.
One-piece, non-adjustable anchors used for attaching brick veneer to an existing concrete wall which contains Standard 1" deep x 1" wide dovetail slot with a 5/8" throat at the face of concrete.
Can also be used with Wood or CMU backup as a single anchor fastened to the backup for brick veneer without exterior insulation in the cavity.
For attaching brick veneer to concrete backup walls with #100 dovetail anchor slot.
Made to Order.
For concrete backups with cast-in-place dovetail anchor slot. Flat anchor allows for field bending.
Specify thickness and length from face of concrete. Anchor is 1" wide.
Available in Stainless Steel and Zinc Alloy 710.
Stainless type 304 or type 316
Available Thickness: 1/4", 3/16", 1/8" or 12 gauge
Zinc Alloy Firewall only available in 1/8"
For concrete backups with cast-in-place dovetail anchor slot. Used to attach CMU or stone.
Specify thickness, length from face of concrete, bend length and type of steel. Width is 1".
Available in Type 304 or Type 316 Stainless Steel
Thickness Available: 1/4", 3/16", 1/8" and 12 gauge
Made to Order.
For concrete backup walls with cast in place dovetail anchor slot. Used to attach CMU and stone.
Specify thickness, length from face of concrete, split bend length and type of steel. Width is 1".
Available Thickness: (1/4") (3/16") (1/8") (12 gauge)
Available in Type 304 or Type 316 Stainless Steel.
Made to Order.
For concrete backups with cast-in-place dovetail anchor slot. Made-to-order. Used to attach CMU or stone veneers.
Anchor Thickness: (1/4") (3/16") (1/8") (12 gauge)
Dowel Diameter: (1/4") (3/8")
Specify thickness, length from face of concrete, diameter and length of pin, location of pin and steel type. Width is 1". Specify if pin is loose or welded.
Available in Type 304 or Type 316 Stainless Steel.
Screw On Channel slots have two tabs that allow attachment to the backup with screws or expansion anchors. These tabs are level with the backup wall. They are typically attached to existing backup walls of wood, concrete, brick or CMU. Various channel slot anchors.
#213 Double Pintle Plate Veneer Anchors are attached directly to the backup system. Insulation/mineral wool is then placed above and below the horizontal tab. Use with #263 Double Pintle Wire Tie.
#213 Plate Tab Sizes: no insulation, 1", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4"
#263 Wire Pintles 3/16" dia Lengths: 3-1/4", 4-1/4", 5-1/4"
Available in Hotdip Galvanized After Fabrication and Type 304 Stainless Steel
NOTE - THE 282 HAS BEEN CHANGED TO NUMBER 263
Used as a 2-piece adjustable anchor for attaching brick veneer to a solid backup wall or one with Gypsum Sheathing or Plywood. This is not for use with polyiso insulation or mineral wool.
12 or 14 gage thick x 1-1/4" wide x 5-1/2" long with 5/16" holes
Available Type 304 Stainless Steel and Hotdip Galvanized
Use with #316 Triangle Wire Ties
The #316 Triangle Wire Tie is used for attaching brick veneers to backup systems that require an adjustable anchoring system. The wire triangle is hooked onto one of various backup anchors and is then embedded in the veneer wall mortar joint.
3/16" Diameter in lengths of: 3", 4", 5", 6", 7" and 9"
Available in Type 304 Stainless Steel and Hot Dip Galvanized
Masonry Wire Ties
One-piece, non-adjustable anchors used for attaching brick veneer to an existing concrete wall which contains Standard 1" deep x 1" wide dovetail slot with a 5/8" throat at the face of concrete.
Can also be used with Wood or CMU backup as a single anchor fastened to the backup for brick veneer without exterior insulation in the cavity.
This non-adjustable wire wall tie is used to bond masonry veneer to a masonry back-up wall, or to bond two masonry walls. The TMS402 Masonry Building Code no longer allows drips on anchors.
Standard: 3/16" diameter with 2" bends in lengths of 6", 8", 10" and 12".
Hot dip galvanized and Stainless Steel.
Special sizes are available.
This non-adjustable wire wall tie is used to bond masonry veneer to a masonry back-up wall, or to bond two masonry walls. The TMS402 Masonry Building Code no longer allows drips on anchors.
Standard: 3/16" diameter Width: 2" and 4"
Length: 6", 8", 10" and 12"
Hot dip galvanized and Stainless Steel.
Specials are available.
Used to secure a masonry veneer to a masonry backup wall. The #262 Double Eye Rod anchor is embedded in the backup CMU and has two eyelets for the #263 Pintle Wire Tie.
Available in Stainless Steel or Hotdip Galvanized
Used to secure a masonry veneer to a masonry backup wall with #262 Double Eye Rod, #213 Double Pintle Brick Veneer Anchor or #1300 Pintle/Eye Wire reinforcement.
The #316 Triangle Wire Tie is used for attaching brick veneers to backup systems that require an adjustable anchoring system. The wire triangle is hooked onto one of various backup anchors and is then embedded in the veneer wall mortar joint.
3/16" Diameter in lengths of: 3", 4", 5", 6", 7" and 9"
Available in Type 304 Stainless Steel and Hot Dip Galvanized
Used to attach CMU horizontally to backup walls or steel beams.
3/16" diameter x 12" long for CMU
Sizes
4" wide for 6" wall
6" wide for 8" wall
8" wide for 10" wall
10" wide for 12" wall
Available in Stainless Steel and Hot Dip Galvanized.
Used to center vertical rebar in CMU walls before grout is poured.
9 gauge wire: Two Block Sizes 8" and 12".
Available in Hot Dip Galvanized.
Channel Slot Systems
Used for attaching masonry/veneers or block to an existing backup wall with attached Channel Slots. The 12 gauge clip is attached to 3/16" diameter wire triangle ties in lengths of 3", 4", 5", 6", 7" and 9".
Available in Stainless Steel and Hotdip Galvanized
Channel slots are welded to structural columns for adjustable attachment of masonry/veneer walls or can be attached to CMU and concrete walls using fasteners through the two holes at the top and bottom of the slot. They can also be used to replace dovetail anchor systems for concrete walls that were not cast with dovetail slots. Use with Channel Slot Anchors.
Screw On Channel slots have two tabs that allow attachment to the backup with screws or expansion anchors. These tabs are level with the backup wall. They are typically attached to existing backup walls of wood, concrete, brick or CMU. Various channel slot anchors
Channel slots are attached to structural columns, brick, CMU or concrete walls. Various channel slot anchors are available for veneer attachment. They can also be used to replace dovetail anchor systems for concrete walls that were not cast with dovetail slots. Use with Channel Anchors.
Available in Stainless Steel
Used for attaching brick veneer to an existing backup wall which has Channel Slots attached.
Available Thickness: 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge
Stainless Steel
Specify thickness, length from face of channel. Width is 1-1/4".
Made to Order
Used to attach stone or CMU to backup walls with attached Channel Slots. Specify thickness, length from face of channel, steel type, and bend length. Width is 1-1/4".
Available in Type 304 or Type 316 Stainless Steel and Zinc Alloy 710 Firewall (1/8" only)
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Made to Order.
Used to attach stone and CMU to backup walls with attached Channel Slots. Specify thickness, length from face of channel, length of split-bends and steel type. Width is 1-1/4".
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Made to Order.
Used to attach stone or CMU to backup walls with attached Channel Slots. Specify thickness, length from face of channel, steel type, pin diameter and length, and pin location from end of anchor. Width is 1-1/4".
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Made to Order
Used to attach stone or CMU to backup walls with attached Channel Slots. The anchor is provided flat for field bending. Specify thickness, length from face of channel, and steel type. Width is 1-1/4"
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Dovetail Anchoring System
Used for attaching brick veneer or stone to a concrete backup wall. The dovetail slot is nailed to the inside of the form. When the concrete is poured and the form is removed, the slot allows anchors to be installed and adjusted vertically.
Standard Size: 1" x 1" narrowing down to a 5/8" throat in 10 foot lengths. The slot is filled with flexible foam filler to prevent concrete from entering the slot during the pour.
Available in 16 and 22 gauge in Type 304 Stainless Steel and 16 gauge in Hotdip Galvanized After Fabrication.
One-piece, non-adjustable anchors used for attaching brick veneer to an existing concrete wall which contains Standard 1" deep x 1" wide dovetail slot with a 5/8" throat at the face of concrete.
Can also be used with Wood or CMU backup as a single anchor fastened to the backup for brick veneer without exterior insulation in the cavity.
For attaching brick veneer to concrete backup walls with #100 dovetail anchor slot.
Made to Order
For concrete backups with cast-in-place dovetail anchor slot. Flat anchor allows for field bending.
Specify thickness and length from face of concrete. Anchor is 1" wide.
Available in Stainless Steel and Zinc Alloy 710.
Stainless type 304 or type 316
Available Thickness: 1/4", 3/16", 1/8" or 12 gauge
Zinc Alloy Firewall only available in 1/8"
Made to Order
For concrete backups with cast-in-place dovetail anchor slot. Used to attach CMU or stone.
Specify thickness, length from face of concrete, bend length and type of steel. Width is 1".
Available in Type 304 or Type 316 Stainless Steel
Thickness Available: 1/4", 3/16", 1/8" and 12 gauge
Made to Order.
For concrete backup walls with cast in place dovetail anchor slot. Used to attach CMU and stone.
Specify thickness, length from face of concrete, split bend length and type of steel. Width is 1".
Available Thickness: (1/4") (3/16") (1/8") (12 gauge)
Available in Type 304 or Type 316 Stainless Steel.
Made to Order
For concrete backups with cast-in-place dovetail anchor slot. Made-to-order. Used to attach CMU or stone veneers.
Anchor Thickness: (1/4") (3/16") (1/8") (12 gauge)
Dowel Diameter: (1/4") (3/8")
Specify thickness, length from face of concrete, diameter and length of pin, location of pin and steel type. Width is 1". Specify if pin is loose or welded.
Available in Type 304 or Type 316 Stainless Steel.
Stone Anchors
The Pos-I-Tie. KeyBolt is designed for easy and effective stone anchor attachment where sheathing/insulation is installed over the backup wall. The KeyBolt system penetrates the sheathing, drills into the backup, and seals the hole to avoid water/air penetration. All compression loads are transferred to the backup through the KeyBolt without damaging the sheathing. When ordering, specify the type of stone anchor with the “KeyBolt Slot".
KeyBolt Barrel Components
Pos-I-Tie. KeyBolt barrel (including 2 hex nuts and EPDM washer
Barrel screw (self-drilling screw, concrete screw, or structural steel screw)
Anchor with KeyBolt Slot
Made to Order
For concrete backups with cast-in-place dovetail anchor slot. Flat anchor allows for field bending.
Specify thickness and length from face of concrete. Anchor is 1" wide.
Available in Stainless Steel and Zinc Alloy 710.
Stainless type 304 or type 316
Available Thickness: 1/4", 3/16", 1/8" or 12 gauge
Zinc Alloy Firewall only available in 1/8"
Made to Order
For concrete backups with cast-in-place dovetail anchor slot. Used to attach CMU or stone.
Specify thickness, length from face of concrete, bend length and type of steel. Width is 1".
Available in Type 304 or Type 316 Stainless Steel
Thickness Available: 1/4", 3/16", 1/8" and 12 gauge
Made to Order.
For concrete backup walls with cast in place dovetail anchor slot. Used to attach CMU and stone.
Specify thickness, length from face of concrete, split bend length and type of steel. Width is 1".
Available Thickness: (1/4") (3/16") (1/8") (12 gauge)
Available in Type 304 or Type 316 Stainless Steel.
Made to Order
For concrete backups with cast-in-place dovetail anchor slot. Made-to-order. Used to attach CMU or stone veneers.
Anchor Thickness: (1/4") (3/16") (1/8") (12 gauge)
Dowel Diameter: (1/4") (3/8")
Specify thickness, length from face of concrete, diameter and length of pin, location of pin and steel type. Width is 1". Specify if pin is loose or welded.
Available in Type 304 or Type 316 Stainless Steel.
Made to Order
Used to attach stone or CMU to backup walls with attached Channel Slots. Specify thickness, length from face of channel, steel type, and bend length. Width is 1-1/4".
Available in Type 304 or Type 316 Stainless Steel and Zinc Alloy 710 Firewall (1/8" only)
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Made to Order.
Used to attach stone and CMU to backup walls with attached Channel Slots. Specify thickness, length from face of channel, length of split-bends and steel type. Width is 1-1/4".
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Made to Order.
Used to attach stone or CMU to backup walls with attached Channel Slots. Specify thickness, length from face of channel, steel type, pin diameter and length, and pin location from end of anchor. Width is 1-1/4".
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Made to Order
Used to attach stone or CMU to backup walls with attached Channel Slots. The anchor is provided flat for field bending. Specify thickness, length from face of channel, and steel type. Width is 1-1/4"
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, bend lengths and steel type.
Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge and 16 gauge
Available in Type 304 and Type 306 Stainless Steel, and Zinc Alloy 710 Firewall material (1/8" only)
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, bend lengths and steel type.
Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge and 16 gauge
Available in Type 304 and Type 316 Stainless Steel, and Zinc Alloy 710 Firewall (1/8" only)
Made to Order
For tying stone or CMU walls together.
3/16" or 1/8" in Type 304 or Type 316 Stainless Steel.
Available Twist thickness & widths
Thickness 3/16", Max SS Width 1-1/4"
Thickness 1/8", Max SS Width 1-1/2"
Made to Order.
Specify thickness, length, width, bend lengths, location of twist and steel type.
Available in Type 304 or Type 316 Stainless Steel
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, bend length and steel type.
Available Thickness: 1/2", 3/8", 1/4", 3/16" 1/8" 12 gauge, 14 gauge, 16 gauge.
Available in Type 304 and Type 316 Stainless Steel
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, bend length, split bend length and steel type.
Available in Type 304 and Type 316 Stainless Steel
Thickness: 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, split bend length and steel type.
Available Thickness: 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge
Available in Type 304 and Type 316 Stainless Steel
Flat section allows for field bending for accurate placement.
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, pin diameter and pin length, location of pin and steel type.
Available Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge
Pin Diameters: 1/4", 3/8", 1/2", 5/8"
Available in Type 304 and Type 316 Stainless Steel.
Pin available Loose or Welded.
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, pin diameter and length, location of pin and steel type.
Available Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge
Pin Diameters: 1/4", 3/8", 1/2", 5/8"
Available in Type 304 and Type 316 Stainless Steel
Specify Location of Welded Pin from center of pin to end. 1/2" minimum of steel between end of anchor and start of hole is recommended.
Made to Order.
Specify thickness, length, width, pin diameter and length, Location of Pin from center of pin to end and steel type. 1/2" minimum of steel between end of anchor and start of hole is recommended.
Available Thickness: 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge
Pin Diameters: 1/4", 3/8", 1/2", 5/8"
Available in Type 304 and Type 316 Stainless Steel
Pins are available loose or welded in place.
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, bend length, pin diameter and length, location of pin and steel type.
Available in Type 304 and Type 316 Stainless Steel.
Available Thickness: 1/2", 3/8", 1/4", 3/16" 1/8", 12 gauge, 14 gauge, 16 gauge.
Available Pin Diameters: 1/4", 3/8", 1/2", 5/8"
Specify gauge, width, length, bend length pin diameter and pin length.
Specify Location of Welded Pin from center of pin to end. 1/2" minimum of steel between end of anchor and start of hole is recommended.
Pins are available loose or welded in place
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, split bend length, pin diameter and length, location of pin and steel type.
Available in Type 304 and Type 316 Stainless Steel.
Available Thickness: 3/8", 1/4", 3/16" 1/8", 12 gauge, 14 gauge, 16 gauge.
Available Pin Diameters: 1/4", 3/8", 1/2", 5/8"
Pin can be welded or loose.
Specify Location of Welded Pin from center of pin to end. 1/2" minimum of steel between end of anchor and start of hole is recommended.
Made to Order
Specify diameter, length and steel type.
Available Diameters: 3/16", 1/4", 3/8", 1/2", 5/8", 3/4"
Available in Type 304 and Type 316 Stainless Steel
Made to Order.
For tying stone or CMU walls together. Specify thickness, length, width, pin diameters and lengths, location of pins and steel type.
Available in Type 304 and Type 316 Stainless Steel.
Available Thickness: 3/8", 1/4", 3/16" 1/8", 12 gauge, 14 gauge, 16 gauge.
Available Pin Diameters: 1/4", 3/8", 1/2", 5/8"
Specify Location of Pins from center of pins to ends. 1/2" minimum of steel between end of anchor and start of hole is recommended.
Pins are available welded or loose.
Made To Order.
Specify Thickness, length, width, pin diameters and lengths, pin locations from ends of anchor and steel type.
Available in Type 304 and Type 316 Stainless Steel.
Available Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.
Available Pin Diameters: 1/4", 3/8", 1/2", 5/8"
Pins are welded in place.
Made to Order
Specify thickness, length and width of strap and the diameter, length and location of the centered welded pin.
Available Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.
Available Pin Diameters: 1/4", 3/8", 1/2", 5/8"
Available in Type 304 and Type 316 Stainless Steel.
Made to Order
Specify thickness, length and width of plate. diameter and length of rod, length of bend and type of steel.
Available Plate Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.
Available Rod Diameters: 1/4", 3/8", 1/2", 5/8"
Available in Type 304 and Type 316 Stainless Steel.
Made to Order
Specify diameter, overall length, bend length and steel type..
Available Rod Diameters: 1/4", 3/8", 1/2", 5/8", 3/4"
Available in Type 304 and Type 316 Stainless Steel.
Custom Z-Shape made to order.
Specify diameter, rod length, rod bends and steel type.
Available Rod Diameters: 1/4", 3/8", 1/2", 5/8", 3/4"
Available in Type 304 and Type 316 Stainless Steel
Made to Order
Specify diameter, overall length, length of bends and steel type.
Available Rod Diameters: 1/4", 3/8", 1/2", 5/8", 3/4"
Available in Type 304 and Type 316 Stainless Steel.
Made to Order
Specify diameter, overall length, J-opening, J-return and steel type.
Available in Type 304 and Type 316 Stainless Steel.
Available Rod Diameters: 1/4", 5/16", 3/8", 1/2"
Minimum J-opening is twice the rod diameter.
(See product 163 for threaded version)
Made to Order.
Specify diameter, overall length, inside dimension of eye and steel type.
(Minimum inside diameter of eye must be twice material diameter)
Available Rod Diameters: 1/4", 3/8", 1/2", 5/8", 3/4"
Available in Type 304 and Type 316 Stainless Steel.
Made To Order
Specify diameter, overall length, bend length, steel type and length of threads.
Available in Stainless Steel, Hot Dip Galvanized and Plain Steel.
See Submittal Sheet under "References" below for sizes.
Made to Order.
Available Rod Diameters: 1/4", 3/8", 1/2", 5/8", 3/4"
Specify Diameter, overall length, thread length, J-opening inside dimension, J return and steel type.
Note: Minimum opening of "J" is twice the rod diameter.
Available in Stainless Steel. Plain Steel
Made to Order
Specify diameter, overall length, inside dimension of eye, length of thread and steel type.
Available Rod Diameters: 1/4", 3/8", 1/2", 5/8", 3/4"
(Minimum inside diameter of eye must be twice material diameter)
Available in Stainless Steel and Plain Steel.
Continuous Threaded Rods cut to order.
Available Rod Diameters: 3/16", 1/4", 3/8", 1/2", 5/8", 3/4"
Specify diameter and length.
Specify dowel cut or deburred (deburr 1 end or both).
(Dowel cut threaded rods are used to bond stone and are not used with nuts. If your threaded rod requires nuts specify deburred.)
Type 304 Stainless Steel
Made to Order
Available Rod Diameters: 1/4", 3/8", 1/2", 5/8", 3/4"
Specify diameter and length of rod, thread length, length of top "T" portion and steel type.
Available in Type 304 Stainless Steel
Made to Order
Specify thickness, length, width, notch dimensions and location, threaded rod diameter, rod length beyond anchor and steel type.
Available in Stainless Steel and Hot Dip Galvanized.
Made to Order.
Corrugated Strap typically embedded in a masonry wall with the welded threaded rod extending out from the wall.
Specify thickness, length and width of corrugated strap, diameter and length of welded threaded rod and steel type.
Available in Stainless Steel and Hot Dip Galvanized.
Made to Order.
Specify thickness, strap length, width, pin diameter and length, location of pin, diameter of threaded rod, length of threaded rod beyond strap and steel type.
Available in Stainless Steel and Hot Dip Galvanized.
Made to Order.
Specify thickness, strap length, width, bend length, diameter of threaded rod, length of threaded rod beyond strap and steel type.
Available in Stainless Steel and Hot Dip Galvanized.
Made to Order
Used to level and plumb stone. Shims can be cut to any size which combines high compression strength and superior load bearing surface contact characteristics.
Specify thickness, length, width and steel type.
Available in Type 304 Stainless Steel and Plain Steel.
Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.
Made to Order.
Specify thickness, strap length, width, split bend length, diameter of threaded rod, length of threaded rod beyond strap and steel type.
Available in Stainless Steel and Hot Dip Galvanized.
Used to level and plumb stone. Shims are molded from an engineered copolymer plastic material which combines high compression strength and superior load bearing surface contact characteristics.
Available in 2" x 2" in 1/16", 1/8", 1/4" 3/8" and 1" x 1" in 3/8"
MADE TO ORDER
Thickness: 3/8", 1/4", 3/16", 1/8", 11 gage, 12 gage, & 14 gage.
Strap Width: 1-1/4" minimum recommended. Minimum width for 1/4" thick is 2" wide.
Length: Specify length as the outside dimensions between the bends. Bend with Hole: 1" minimum recommended. You should consider the overall length of the anchor and the height of the split bend to make sure there is enough room for the installer to get the screw and tool in place without interference from the split bend.
Hole should be a minimum of 1/16" larger than your screw size. (3/8" screw will use a 7/16" diameter hole).
Split Bend: Minimum 3/4" recommended (specify as o.d. dimension) Available in Type 304 and Type 316 Stainless Steel, Zinc Alloy 710 Firewall Material
Made to Order
Thickness: 3/8", 1/4", 3/16", 1/8", 11 gage, 12 gage, & 14 gage.
Strap Width: 1-1/4" minimum recommended.
Length: Specify length as the outside dimensions between the bends.
Bend with Hole: 1" minimum recommended. You should consider the overall length of the anchor and the height of the bend to make sure there is enough room for the installer to get the screw and tool in place without interference from the U-Bend. Hole should be minimum of 1/16" larger than your screw size. (3/8" screw will use a 7/16" diameter hole).
Bend Length: Minimum 3/4" recommended (specify as o.d. dimension)
Available in Type 304 and Type 316 Stainless Steel and Zinc Alloy 710 Firewall Material.
Made to Order
Thickness: 3/8", 1/4", 3/16", 1/8", 11 gauge, 12 gauge, & 14 gauge.
Width: 1-1/4" minimum recommended.Length: Specify length as the outside dimensions between the bends.
Bend with Hole: 1" minimum recommended. You should consider the overall length of the anchor and the height of the bend to make sure there is enough room for the installer to get the screw and tool in place without interference from the U-Bend. Hole should be minimum of 1/16" larger than your screw size. (3/8" screw will use a 7/16" diameter hole).
Bend Length: Minimum 3/4" recommended (specify as o.d. dimension)
Available in Type 304 and Type 316 Stainless Steel, Zinc Alloy 710 Firewall material
Made to Order
Thickness of Strap: 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge & 16 gauge.
Diameter of Pin: 1/4", 3/8", 1/2", 5/8" Strap Width: 1-1/4" minimum recommended.
Length: Specify length of strap to o.d. of bend and overall length of pin.
Bend Length: minimum 3/4" recommended (specify o.d. dimension)
Available in Type 304 and Type 316 Stainless Steel
Bend Hole: Usually centered in bend. Hole should be 1/16" larger than screw/expansion anchor. (i.e. If using a 1/4" screw the hole diameter would be 5/16".)
Specify Location of Pin from center of pin to end. 1/2" minimum of steel between end of anchor and start of hole is recommended.
Pins are available loose or welded in place.
Made to Order
Specify thickness, length, width, bend length, hole diameter and location, welded plate height and steel type.
Available in Type 304 and Type 316 Stainless Steel
Made to Order
Used for anchoring stone to backups.
Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 11 gauge, 12 gauge, & 14 gauge.
Strap Width: 2-1/2" minimum recommended.
Length: Specify length as the outside dimension of the bend with the slot.
Bend with Holes: Specify outside dimension and the diameter and location of holes in the bend.
Available in Type 304 and Type 316 Stainless Steelxasd
Made to Order
Used for anchoring stone to backups.
Specify thickness, width (3" minimum recommended), length, bend with holes, hole diameter(s) and location(s), split bend dimensions and steel type.
Available in Type 304 and Type 316 Stainless Steel
Made to Order.
Used for stone attachments. The drilled and tapped Barrel is 5/8" or 3/4" diameter x minimum 3" long with a 3/8" (9.5 mm) diameter continuous threaded rod cut to desired length. Type 304 Stainless Steel.
Special Sizes Available, but barrel diameter should always be a minimum of 3/8" diameter larger than the diameter of the threaded rod.
Made to Order
Angle Clip for various attachments.
#341: Specify thickness, length, width, bend length, hole size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order
Angle Clip for various attachments.
#341-A: Specify thickness, length, width, bend length, hole sizes and locations and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 Firewall (1/8" and 16 gauge only)
Made to Order
Angle Clip for various attachments.
#341-B: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342-A: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342: Specify thickness, length, width, bend length, slot size and location and steel type.
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342-B: Specify thickness, length, width, bend length, slot sizes and locations and steel type.
Used to attach a stone panel in between two installed stone panels.
Specify diameter of dowel, length of dowel. Spring length beyond dowel should be the same length as the dowel. The spring compresses to have its length.
Type 304 Stainless Steel.
Stock Sizes:
1/2" diameter and 3/8" diameter x 4" dowel with 4" spring
1/2" diameter and 3/8" diameter x 3" dowel with 3" spring
Custom lengths available
Wire tie anchor used to secure rubble stone veneers to back-up walls. Used with Heckmann's Rubble Stone Veneer Anchor system (#398-C L-Type Rubble clips and #398-J J-Hook Rod). Ideal for when horizontal mortar joints do not align, and a large amount of vertical adjustment is required.
The 398 wire tie is 3/16" diameter. welded rod prevents compression loads from damaging sheathing. Specify tie length.
Available in Stainless Steel and Hot Dip Galvanized
L-Type anchor used to secure rubble stone veneers to back-up walls. Used with Heckmann's Rubble Stone Veneer Anchor system (#398 Rubble Stone Wire Tie and #398-J J-Hook Rod). Ideal for when horizontal mortar joints do not align, and a large amount of vertical adjustment is required.
The 398-C Clip is 12 gauge x 2-3/4" wide. Specify the Length required. The J-Rod is lowered through the slots and require the 398 ties to be pre-loaded between the clips. Clips are typically spaced 16" x 16" or 16" x 24".
Available in Stainless Steel and Hot Dip Galvanized.
J-Hook Rod used to secure rubble stone veneers to back-up walls. Used with Heckmann's Rubble Stone Veneer Anchor system (#398-C L-Type Rubble clips and #398 Rubble Stone Wire Tie). Ideal for when horizontal mortar joints do not align, and a large amount of vertical adjustment is required.
J-Hook Rod: Available in 5/16" and 3/8" diameter typically 52" long. These are inserted down through the 398-C Clips after pre-loading the 398 wire ties between the clips.
Available in Stainless Steel and Hot Dip Galvanized.
Made to Order
Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify angle leg dimensions, thickness, and length.
Made to Order
Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify plate length, width, thickness, diameter and length of headed anchors, and steel type.
Made to Order
Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify length, width, thickness, and hole diameters and locations.
Made to Order
Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify length, width, thickness, hole diameters and locations, and toe bar dimensions and location.
Made to Order
Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify bend dimensions, slot sizes and locations, od length between bends, width of angle, and steel type.
Made To Order
Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify bend dimensions, slot sizes and locations, od length between bends, width of angle, and steel type.
Custom Made
Available in "Z" shape or "U" shape.
Specify Gauge, width, Length, Bend length with hole diameters and locations, bend down length.
Available Type 304 and Type 316 Stainless Steel.
Allows for lateral adjustment for stones with kerfs.
Made to Order - See Submittal Sheet below under References for product details.
Available in type 304 or type 316 stainless steel only.
Allows for lateral adjustment for stones with kerfs.
Made to Order - See Submittal Sheet below under References for product details.
Available in type 304 or type 316 stainless steel only.
Seismic Veneer Anchors
Used for attaching brick veneer to backups in seismic zones requiring a reinforcement wire in the exterior brick veneer. The corrugated end increases adhesion in the mortar joint.
(They can be used in non-seismic walls as regular sheet metal veneer anchors without the seismic wire in the exterior veneer wall. )
Raised tab in flat section allows for placement of Pencil Rod or Masonry Wall Reinforcement that allows for in plane horizontal and vertical movement of the masonry walls while restraining tension and compression.
14 gauge x 1-1/4" wide plus a 1-1/2" bend with a centered 5/16" diameter hole.
Type 304 Stainless Steel.
Available in overall lengths of 2-1/2" 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 7" and 8".
Plastic clip for attaching any 3/16" or 9 gauge masonry veneer anchor to a single horizontal reinforcing wire in the veneer.
9 gauge or 3/16" dia x 10 ft long.
Stainless Steel, Hot Dip Galvanized
See #363 Plastic Seismic Clip for attachment of Continuous wire to wire veneer ties.
Partition Top Anchors
As a Partition Wall Stabilizing Anchor, the Dovetail Rod Anchor is Hotdip Galvanized After Fabrication and is used with a #421 plastic tube. When the block core is filled with grout, the tube allows for vertical deflection. The concrete slab above must have a cast-in-place dovetail anchor slot. Standard Rod when used as a Stabilizing Wall Anchor is 3/8" diameter x 7" long and is not threaded. The welded clip is12 gauge.
Catalog # 121-7H - Standard Hotdip Galvanized After Fabrication.
The #121 Dovetail Threaded Rod Anchor can also be used in veneer walls with concrete backups for bolting back to the backup wall.
Custom rod lengths and diameters are available in Type 304 or Type 316 Stainless Steel.
This anchor is installed by either welding the plate to a structural beam or fastening it to a concrete slab with expansion anchors. The plastic tube is grouted into the CMU cell.
Standard: 3/16" x 1-1/2" wide x 3" long plate with a welded 3/8" diameter x 6-3/4" rod. Two 5/16" diameter holes in the plate for attachment.
Standard size is boxed with the #421 Plastic Tube 5/8" od x 7-1/4" with a compressible filler at the end to prevent grout infiltration. Hot Dip Galvanized.
Custom Sizes are available - order 421 Tubes separately for custom sizes.
This plastic tube is used with #121 Dovetail Rod Anchor and the #419 Pin Stabilizing Anchor. The plastic tube has a foam filler on one end to prevent grout penetration. The rods placed into the tube and the tubes are grouted into the CMU. This allows for vertical deflection of the wall.
Used to resist lateral loads at the top of a masonry wall and allow for vertical deflection. Steel bends will be visible at the top of the CMU wall. Standard is 12 gauge x 8" long with 2" bends and 5/16" holes for block sizes 4", 6", 8", 10" and 12". Available in Mill Galvanized Steel and Hotdip Galvanized After Fabrication. Custom Sizes available. Stainless Steel available.
Firewall Anchors
Made to Order
Used to attach stone or CMU to backup walls with attached Channel Slots. Specify thickness, length from face of channel, steel type, and bend length. Width is 1-1/4".
Available in Type 304 or Type 316 Stainless Steel and Zinc Alloy 710 Firewall (1/8" only)
Available thickness: 1/4", 3/16", 1/8", 12 gauge, 14 gauge
Used for attaching brick veneer to Wood backups.
Standard: 16 gauge x 1-1/4"wide with a 1-1/2" bend with a centered 5/16" diameter hole.
Steel Types: Type 304 Stainless Steel, Hotdip Galvanized after fabrication or Zinc Alloy 710 (1/8" thick only) for Firewalls.
Standard Lengths: 3-1/2" and 5-1/2"
For Custom Sizes see #340-A Corrugated L-Anchor with Hole
Used to attach CMU walls to structural steel beams
Order in pairs, one left and one right side anchor
Standard size: 7" L x 2" W, 1/8" thick with a 1-1/2" L-shaped bend
Standard Notch: 5/8" W x 1" D, begins 1" from end of anchor
Available in Stainless Steel and Zinc Alloy 710 Firewall (1/8" only)
Made to Order
Thickness: 3/8", 1/4", 3/16", 1/8", 11 gage, 12 gage, & 14 gage.
Strap Width: 1-1/4" minimum recommended. Minimum width for 1/4" thick is 2" wide.
Length: Specify length as the outside dimensions between the bends. Bend with Hole: 1" minimum recommended. You should consider the overall length of the anchor and the height of the split bend to make sure there is enough room for the installer to get the screw and tool in place without interference from the split bend.
Hole should be a minimum of 1/16" larger than your screw size. (3/8" screw will use a 7/16" diameter hole).
Split Bend: Minimum 3/4" recommended (specify as o.d. dimension) Available in Type 304 and Type 316 Stainless Steel, Zinc Alloy 710 Firewall Material
Made to Order
Angle Clip for various attachments.
#341: Specify thickness, length, width, bend length, hole size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order
Angle Clip for various attachments.
#341-A: Specify thickness, length, width, bend length, hole sizes and locations and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 Firewall (1/8" and 16 gauge only)
Made to Order
Angle Clip for various attachments.
#341-B: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.
Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342-A: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342: Specify thickness, length, width, bend length, slot size and location and steel type.
Made to Order.
Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.
#342-B: Specify thickness, length, width, bend length, slot sizes and locations and steel type.
Made to Order
Efficiently transfers horizontal forces between a masonry wall and the building frame. The Twist-On Anchor allows you to connect a masonry wall to a Joist, Joist Girder or any other Truss as well as to a Castellated or Rolled Beam while allowing free deflection.
3-1/4" wide. Specify anchor length, vertical sliding bar dimension (1/2", 3/4" or 1") and steel type. Vertical Rod can be round or square.
Stainless Steel available in 3/16" or 1/8" thickness.
Zinc Alloy 710 Firewall available in 1/8" only.
Rebar Positioners
Used to center vertical rebar in CMU walls before grout is poured.
9 gauge wire: Two block sizes 8" and 12"
Used to center vertical rebar in CMU walls before grout is poured.
9 gauge wire: Two Block Sizes 8" and 12".
Available in Hot Dip Galvanized.
Concrete Accessories
Made to Order
Used to level and plumb stone. Shims can be cut to any size which combines high compression strength and superior load bearing surface contact characteristics.
Specify thickness, length, width and steel type.
Available in Type 304 Stainless Steel and Plain Steel.
Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.
Used to level and plumb stone. Shims are molded from an engineered copolymer plastic material which combines high compression strength and superior load bearing surface contact characteristics.
Available in 2" x 2" in 1/16", 1/8", 1/4" 3/8" and 1" x 1" in 3/8"
When cast into concrete, Shelf Angle Wedge Inserts and Askew Head Bolts provide a secure and adjustable method for fastening shelf angles and other materials to concrete structures. The inserts allow vertical adjustment so veneers can be properly aligned despite construction tolerances in the building frame.
For 3/4" Bolts only. Malleable Iron Inserts Hot Dip Galvanized
Two Sizes:
Regular: Overall Height 3-7/8" with 1-3/4" vertical adjustment
Long: Overall Height 5-1/2" with 3" vertical adjustment
See product 427 Askew Head Bolts for the bolts.
When cast into concrete, Shelf Angle Wedge Inserts and Askew Head Bolts provide a secure and adjustable method for fastening shelf angles and other materials to concrete structures.
Askew Head Bolts are available 3/4" diameter, Hotdip Galvanized After Fabrication in lengths of 2", 2-1/2", 3", 4" and 6".
See #425 for the Shelf Angle Insert.
Sold with or without #685-75H Hotdip Washers and #681-75H Hotdip Nuts
See 442 Plastic Horse-Shoe Shim Washers and 443 Steel Horse-Shoe Shim Washers for the shims.
Used to shim shelf angles when concrete walls are not plumb.
High Impact multi-polymer plastic shims with compressive strength between 8,000 and 10,000 psi.
Used for shimming anchors and angles for out-of-plumb walls.
Standard stock sizes are 4" x 3" Hotdip Galvanized with a 13/16" x 3" slot in thicknesses of 1/16", 1/8", 1/4", 3/8" and 1/2".
Custom sizes are available in Stainless Steel, Plain Steel, Hotdip Galvanized, or Mill Galvanized (1/16" and 1/8" only for mill galv).
Control and Expansion Joints
Control Joint Anchors are designed to transfer loads across control joints. They are also intended to handle compression loads and control lateral movement.
22 gauge x 1-1/2" wide x 10" overall length.
Available
Stainless Steel / Plastic
Type 304 all Stainless Steel
Mill Galvanized
Moisture Control & Flashing Products
Cell vents are installed in the bottom vertical mortar joint of a brick veneer wall to allow moisture to vent out of a cavity wall. Cell vents are also installed at the top of the wall to allow ventilation in the cavity. They consist of many small adjacent passageways, which allow moisture to vent from the cavity to the exterior of the building while restricting ingress of insects. The cellular composition provides easy drainage for moisture along the full height of the head joint. Cell vents are UV-resistant and tested in conformance to ASTM D2240, D790B, D638 and D1238B.
Regular Size: 3/8" thick x 2-1/2" high x 3-3/8 deep.
Jumbo Size: 3/8" thick x 3-1/2" high x 3-3/8" deep.
Available in Tan, Brown, Clear, Cocoa, Black, White and Gray
Louvered Weep Vents come in three sizes: Standard (85LSTD) 2-1/2", Medium (85LCSR) 2-3/4" and Jumbo (i5LJUM) 3-5/8". Louvered front allows water to leave and not re-enter. Available in Gray only.
200 pcs per box.
Used as flashing material to prevent water damage. The standard 1/2" drip-edge is folded back to prevent sharp edge on exterior of wall. Available in Stainless Steel.
Standard is 3" wide x 8 ft in 26 gauge. Custom widths are available.
For securing flashing to a backup wall.
Standards:
1050-T1-SS: 1/8" x 1" wide x 8ft Stainless - no lip
1050-T2-P 1/8" x 1" wide x 8ft - plastic - with lip
1050-T1-A 14 gauge x 1" x 8ft Aluminum - no lip
1050-T2-A 14 gauge x 1" x 8ft Aluminum - with lip
1050-T2-SS 26 gauge x 1-1/2" wide x 8ft - with lip
Custom Sizes available
Specify thickness, width, length, hole size, hole spacing and steel type.
Weep-Thru Mortar Deflector is designed to catch mortar droppings and allow masonry cavity drainage through the weep holes. It has a three dimensional geometric patterned core and is designed to be 10 inches (25.4 cm) high in the cavity wall.
Allows cavity drainage and protects flashing.
Dovetail configuration allows mortar droppings to rest on two levels crating open areas for
proper water drainage.When properly installed, will prevent clogging of weep holes.
Will not grow mold.
Polymer core is resistant to most known corrosive chemicals, including solvents.
10 inch width suspends mortar droppings above the weep holes, but below the flashing
connection to the interior wall.Easy installation. No mechanical fasteners required. Lay first 2 courses of brick and then install Mortar deflector in cavity.
Packaged in boxes of 5 foot pcs.
Catalog #84-5 - 1/2" thick (Actual .4") - 50 pcs per box
Catalog # 84-1 - 1" thick - 20 pcs per box
Catalog # 84-2 - 2" thick - 20 pcs per box
Prefabricated soldered Outside Corner Flashing is placed underneath wall flashing for protection from moisture penetration into the building interior.
STANDARD:
* 237-S 10" x 10" x 4" Stainless Corner
SPECIALS:
* 237-C 10" x 10" x 4" Copper Corner
* 2372-S 12" x 12" x 3" Stainless Drip Edge
* 2372-C 12" x 12" x 3" Copper Drip Edge
Prefabricated soldered Inside Corner Flashing is placed underneath wall flashing for protection from moisture penetration into the building interior.
26 gauge stainless steel
16 oz (24 gauge) copper
24 gauge Mill Galvanized
STANDARD:
* 238-S 6" x 4" x 4" Stainless Steel Corner
SPECIALS:
* 238-C 6" x 4" x 4" Copper Corner
* 2382-S 12" x 12" x 3" Stainless Drip Edge
* 2382-C 12" x 12" x 3" Copper Drip Edge
* 238-G 4-7/8" x 4-7/8" x 4" 24 gauge Mill Galv Corner
Prefabricated soldered End Dam is placed underneath wall flashing for protection from moisture penetration into the building interior.
STANDARD:
* 239-S 4" x 4" x 4" 26 gauge Stainless Steel
SPECIAL:
* 239-C 4" x 4" x 4" 16 oz (24 gauge) Copper
Miscellaneous Items
Made to Order
Used to level and plumb stone. Shims can be cut to any size which combines high compression strength and superior load bearing surface contact characteristics.
Specify thickness, length, width and steel type.
Available in Type 304 Stainless Steel and Plain Steel.
Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.
Used to level and plumb stone. Shims are molded from an engineered copolymer plastic material which combines high compression strength and superior load bearing surface contact characteristics.
Available in 2" x 2" in 1/16", 1/8", 1/4" 3/8" and 1" x 1" in 3/8"
Remedial Wall Tie provides a quick, effective and economical solution for securing and stabilizing masonry. Existing facades constructed of brick, stone, masonry, precast concrete, etc. that have wall ties missing or corroded, can be re-attached using Remedial Tie without removing the veneer. This stainless-steel helical tie is dry set. The Remedial Tie cuts a threaded groove into the masonry as it is driven into position through a pre-drilled pilot hole. The end result is a strong and permanent connection between wythes without the use of toxic adhesives or rigid mechanical connectors
Stainless Steel
Glass Block Panel Anchors are used to tie the glass block to the jambs and head. They are installed at both jams under the expansion strip in every other course.
Made to Order
Specify length, width, thickness, centered hole diameter and steel type.
Available in Type 304 Stainless Steel, Type 316 Stainless Steel and Plain Steel.
Available Thickness: 14 gauge, 12 gauge, 1/8", 3/16", 1/4", 3/8" x 1/2"
Expert Advice
The Pos-I-Tie® was invented in 1985 and was the first barrel type veneer anchor in the marketplace. This system allows the transfer of lateral loads between the brick veneer and the backup directly through full sheets of sheathing without imparting any forces onto the sheathing. Not all sheathing is the same. It is important to analyze the wall configuration to determine the type and size of your masonry anchor to insure the correct Pos-I-Tie® is used for your project.
Solid Brick vs Brick Veneer
There are two ways to build a brick building: solid masonry and brick veneer. Is one better than the other? If so, why?
Solid Masonry
Solid masonry is the good old-fashioned brick construction that was quite common up until the mid-1900s. This is also known as ‘double brick,' ‘solid brick,' or ‘brick and block' construction. This form of masonry construction uses several layers (wythes) of brick with header bricks to hold them together. Some solid masonry walls built before 1900 were over 20" thick! Because the inner wythe can't be seen from the outside it was commonly substituted with concrete or cinder block. Sometimes metal ties were incorporated into solid masonry walls. Unfortunately, older solid walls with these ties didn't use hot-dip or stainless steel ties so most of those original ties have rusted away.
Solid masonry was undeniably a solid way to build. With an 8 inch or greater wall thickness, they were able to support a wide variety of different roof structures. Carpenters often worked together to build the floor joists into the walls at the same time the brick was going up.
In the United States, The TMS 402 building code allows for the use of Hot-Dip Galvanized Steel and Type 300 Stainless Steel for anchors in exterior walls. How does one decide which material they should employ in their construction project? Both are high-quality materials and provide an impressive amount of corrosion resistance, but each has its own vulnerabilities and strengths and both should be considered when specifying building materials.
The first difference between the two materials is the way that they are manufactured. Stainless is an alloy steel, which means that it contains between 16 to 24 percent chromium, up to 35 percent nickel, and small amounts of carbon and manganese. To create stainless steel, ordinary steel, chromium, and the other elements are blended in their molten state. To create galvanized steel, ordinary steel is coated by dipping the products in melted molten zinc, hence the name “hot-dipped."
The Pos-I-Tie® is a 2-piece adjustable veneer anchor. The Pos-I-Tie system has been the premier anchor of choice for mason contractor's all over the country. Pos-I-Tie was the first barrel-screw masonry anchor back in 1985 and is still the first choice of architects and contractors. It is available in three different styles.
The 2016 version of the Masonry Building Code has been accepted as a part of the 2018 International Building Code. Earlier code modifications have taken place in 2013, 2011, 2008 and 2005 and the next version will not be out until 2022. Below are the current code requirements for masonry anchors. Please be aware that these are the “minimum" requirements for code compliance.
Key Features of the TMS402/602-16 Building Code
Backup walls must be designed to resist water penetration. Water entering the interior is one of the main causes of brick veneer failures. Water will get in the cavity so the proper design of keeping the water from entering the building by waterproofing the backup and getting it out of the air cavity is vital.
Flashing and weep holes must be designed to eliminate the water in the cavity. The code specifies minimum 3/16" i.d. weep tubes spaced less than 33 inches on center. (While this does drain water, it does not ventilate the cavity. In order to get good airflow to dry out the cavity, Heckmann's recommends using a vent-type weep system that is the full height of the brick manufactured from a polyester mesh or a cell-type polypropylene material and spaced no more than 24" apart. Vents should also be installed at the very top course of the wall to allow airflow through the entire cavity for drainage and drying.)
Excavations throughout Europe have found stone used for shelter as far back as 12,000 B.C. The Egyptians built the pyramids around 2550 BC and the Romans established a stone quarry around 173 BC. Today, stone remains one of the strongest and most durable building products on the planet. When using stone as a veneer, engineering and design are critical factors in a successful building project. The majority of stone projects are unique and require custom anchors.
For slab-type anchored veneer, the International Building Code specifies a minimum of four anchors per unit with tie spacing not exceeding 24 inches. The maximum area of a unit is limited to 20 square ft. Veneer ties for slab-type veneer are required to resist two times the weight of the anchored veneer in tension or compression. Wire stone anchors must be a minimum of 9 gauge diameter (.1483 inches). Non-wire stone anchors are to have a minimum width of 1".
The TMS402 Building Code Requirements and Specification for Masonry Structures list several references and guidelines for adhered veneer. Anchored dimensional stone is not currently covered under the code and is considered a “special system" that requires engineering.
Visit our Sister Company
TOGGLER® was founded in 1968 and is the only manufacturer that designs, patents, and makes all of its anchors in the USA
Family-owned and established in 1952
High-performance anchors you can trust engineered here in the USA. We never compromise on quality. So you don't.Expansion Anchors