Lightning Protection
Cast bronze wedge is used when coursing cable through 3/4" diameter copper conduit. Wedges must be used to bond cable on each end of conduit. Wt. .04 lbs. each.
The Cripe Lightning Rod Company, a predecessor company, was founded in the mid-1920's by Henry H. Cripe and his sons. The company manufactured, installed, and serviced lightning protection systems and began operations out of a barn located on the company's present facilities in Goshen, Indiana.
In 1934 during the Great Depression, son Earnest C. Cripe established Independent Protection Co., Inc. in Goshen, Indiana to manufacture and install lightning protection systems. Independent Protection Co. continues to be a leading manufacturer of structural lightning protection for industrial, commercial, residential, historical buildings and trees.
Today, the fourth and fifth generations of the Cripe family are actively involved in the business. Rob Cripe, is currently Corporate President and CEO. Evan Cripe and Erica Menzie fill day-to-day duties in sales, operations and HR responsibilities.
Thank you for your interest in the Independent Protection Company and the lightning protection system products that IPC manufactures. Feel free to contact IPC for all of your lightning protection needs.
Aluminum Bases
Cast aluminum base with 1/2″ female
threads. Wt. .16 lbs. each.
Cast aluminum part has 1/2″ female
threads. Wt. .26 lbs. each.
Cast aluminum with 1/2" female threads. Air terminals are offset 1-3/4" from mounting surface. Wt. .25 lbs. each.
Cast aluminum part has 5/8″ male threads. Wt. .24 lbs. each.
Cast aluminum part provided with 1/2″ female threads and two hex-head bolts for securing cable. May be furnished with 5/8″ threads when specified. Wt. .22 lbs. each.
Cast aluminum with 5/8″ male threads. Air terminals are offset 1-3/4″ from surface. Wt. .25 lbs. each.
Cast aluminum base can be used in either a vertical or horizontal mounting. For use with 1/2″ air terminals. Fasten to surface with adhesive or screws. Wt. .28 lbs. each.
Cast aluminum with 1/2″ female threads and over 4 square inches of bonding surface. Wt. .10 lbs. each.
Cast aluminum part is for use with railings up to 1-3/4" diameter. Part is threaded for 5/8" male threads. Adaptor may be required. Wt. .28 lbs. each.
Cast aluminum base support with cable fastener. Cable can run parallel or perpendicular to standing seam. Part is furnished with 5/8″ male threads and for openings up to 7/8″ wide. Wt. .28 lbs. each.
Cast aluminum part is provided with 5/8" male threads and furnished with 5/16" lead anchor and screw. Wt. .28 lbs. each.
Cast aluminum with 1/2" female threads. Wt. .64 lbs. each.
Cast aluminum with 5/8" male threads. Wt. .64 lbs. each.
Cast aluminum part with 1/2" female threads. Wt. .64 lbs. each.
Cast aluminum part with 3/8" female and 5/8" male threads. Wt. .64 lbs. each.
Cast aluminum part is for use with railing up to 1-3/4" diameter. Part is threaded for 1/2" female threads. Wt. .28 lbs. each.
Cast aluminum part has 1/2" female threads. Wt. .26 lbs. each.
Aluminum strap material is 6″ in length for applications where space is limited. Part is furnished with 5/8″ male threads. Wt. .20 lbs. each
Cast aluminum is 6-1/4" in length with 1/2" female threads that accommodates round cable shown below. Wt. .14 lbs. each.
Pressed aluminum strap material 11-3/4" in length with adjustable slider cable support. Part is furnished with 5/8" male threads. Wt. .36 lbs. each.
Pressed aluminum strap material 11-3/4" in length with adjustable slider cable support. Part is furnished with 5/8" male threads. Wt. .28 lbs. each.
Aluminum strap material 11-3/4" in length with adjustable slider cable support. Part is furnished with 1/2" female threads. Wt. .36 lbs. each.
Aluminum strap material is 6" in length for applications where space is limited. Part is furnished with 1/2" female threads. Wt. .20 lbs. each.
Cast aluminum base is 13" in length with 5/8" male threads. Wt. .36 lbs. each.
Cast aluminum has 8 square inches of bonding surface with 5/8" male threads. Wt. .14 lbs. each.
Cast aluminum with 5/8" male threads. Wt. .22 lbs. each.
Cast aluminum base with 5/8" male threads and outer diameter of pan is 6" OD. Pan is fastened with adhesive and filled with stone chips or concrete. Wt..98 lbs. each.
Cast aluminum with 5/8" male threads. Wt. .22 lbs. each.
Cast aluminum base has 1/2" female threads. Wt. .22 lbs. each.
Cast aluminum with 5/8" male threads. Wt. .28 lbs. each.
Cast aluminum with 1/2" female threads. Wt. .26 lbs. each.
Cast aluminum base with adjustable adaptor and is furnished 5/8" male threads. Wt. .36 lbs. each.
Cast bronze base with adjustable adaptor and is furnished with 1/2" female threads. Wt. 1.08 lbs. each.
Cast aluminum part has 8 square inches of bonding surface and has 1/2" female threads. Wt. .12 lbs. each.
Machined brass bushing with 1/2″ male and 3/8″ female threads. Bushing installed in 1/2″ female bases to allow use of 3/8″ Strike Termination Devices. Wt. .02 lbs. each.
Cast bronze fastener with crimp type connector. Base is filled with stone or chips and adhered to roof with adhesive. Outer diameter is 4" with inside diameter at 3-1/2". Wt. .98 lbs. each.
Cast bronze base with 3/8″ female threads and outer diameter of pan is 6″ OD. Pan is fastened with adhesive and filled with stone chips or concrete. Wt. 2.90 lbs.
Cast bronze base has 3/8" female and 5/8" male threads. Wt. .64 lbs. each.
Cast bronze base has 1/2" female threads. Wt. .64 lbs. each.
Cast bronze with 3/8" female and 5/8" male threads. Wt. .96 lbs. each.
Cast bronze with 1/2" female threads. Wt. .86 lbs. each.
Copper, Bronze, Brass Bases
Cast bronze base with 1/2" female threads. Wt. .50 lbs. each.
Cast bronze base with 3/8" female threads. Wt. .46 lbs. each.
Cast bronze for use with 3/8" threaded rod. Part has crimp type cable fastener and set screw. Wt. .22 lbs. each.
Cast bronze with 3/8" female and 5/8" male threads. Air terminals are off–set 1-3/4" from surface. Wt. .76 lbs. each.
Cast bronze with 1/2" female threads. Air terminals are off–set 1-3/4" from mounting surface. Wt. .76 lbs. each.
Cast bronze for use with 3/8" rod with clamp style cable fastener. Wt. .50 lbs
Cast bronze base can be used in either a vertical or horizontal mounting. For use with 3/8" air terminals. Fasten to surface with adhesive or screws. Wt. .80 lbs. each.
Cast bronze base can be used in either a vertical or horizontal mounting. For use with 1/2" air terminals. Fasten to surface with adhesive or screws. Wt. .80 lbs. each.
Cast bronze with 1/2" female threads And over 4 square inches of bonding surface. Wt. .30 lbs. each.
Cast bronze for use with 3/8" threaded rod. Part has crimp type cable fastener and set screw. Wt. .22 lbs. each.
Cast bronze part for use with notched rod. Part has crimp type cable fastener and set screw. Wt. .22 lbs. each.
Cast bronze part has 5/8" male threads. Wt. .84 lbs. each.
Cast bronze part has 3/8" female threads. Wt. .80 lbs. each.
Copper strap material is 6" in length for applications where space is limited. Part is furnished with 3/8" female and 5/8" male threads. Wt. .48 lbs. each.
Copper strap material 11-3/4" in length with adjustable slider cable support. Part is furnished with 1/2" female threads. Wt. .77 lbs. each.
Pressed copper strap material 11-3/4" in length with adjustable slider cable support. Part is furnished with 3/8" female and 5/8" male threads. Wt. .77 lbs. each.
Cast bronze is 6-1/4" in length with 3/8" female threads that accommodates standard flat or round cable. Optional with 1/2" female threads if specified. Wt. .32 lbs. each.
Copper strap material 11-3/4" in length with adjustable slider cable support. Part is furnished with 1/2" female threads. Wt. .77 lbs. each.
Copper strap 11-3/4" in length with clamp down cable connector. Part is furnished with 3/8" female and 5/8" male threads. Wt. .70 lbs. each.
Cast bronze is 6-1/4" in length with 3/8" female threads that accommodates standard flat or round cable. Optional with 1/2" female threads if specified. Wt. .32 lbs. each.
Cast bronze base is 13" in length with 3/8" female and 5/8" male threads. Wt. 1.14 lbs. each.
Cast bronze with 3/8" female and 5/8" male threads. Wt. 1.55 lbs. each.
Cast bronze part with 1/2" female threads. Wt. 1.55 lbs. each.
Cast bronze part with 3/8" female and 5/8" male threads. Wt. 1.75 lbs. each.
Cast bronze part is for use with railing up to 1-3/4" diameter. Part is threaded for 1/2" female threads. Wt. .74 lbs. each.
Cast bronze part is provided with 3/8" female and 5/8" male threads and furnished with 5/16" lead anchor and screw. Wt. .68 lbs. each.
Cast bronze with 1/2" female threads. Wt. 1.55 lbs. each.
Cast Bronze part is for use with railings up To 1-3/4" diameter. Part is threaded for 3/8" female and 5/8" male threads. Wt. 74. lbs. each.
Cast bronze base has 3/8" female and 5/8" male threads. Wt. .64 lbs. each.
Cast bronze fastener with crimp type connector. Base is filled with stone or chips and adhered to roof with adhesive. Outer diameter is 4" with inside diameter at 3-1/2". Wt. .98 lbs. each.
Cast bronze part has 8 square inches of bonding surface and has 1/2" female threads. Wt. .40 lbs. each.
Cast bronze has 8 square inches of bonding surface. With 3/8" female and 5/8" male threads. Wt. .42 lbs. each.
Cast bronze base with adjustable adaptor and is furnished with 3/8" female and 5/8" male threads. Wt. 1.08 lbs. each.
Cast bronze base with adjustable adaptor and is furnished with 1/2" female threads. Wt. 1.08 lbs. each.
Cast bronze base has 1/2" female threads. Wt. .64 lbs. each.
Cast bronze with 3/8″ female and 5/8″ male threads. Wt. .96 lbs. each.
Cast bronze with 1/2" female threads. Wt. .86 lbs. each.
Cast bronze part is provided with 1/2" female threads and furnished with 5/16" lead anchor and screw. Wt. .68 lbs. each.
Cast bronze base support with cable fastener. Cable can run parallel or perpendicular to standing seam. Part is furnished with 3/8" female and 5/8" male threads and for seams up to 3/4" wide. Wt. .93 lbs. each. 22 28S 32S 40 21 G3 A22 A28 A30
Cast bronze part is provided with 1/2" female threads and furnished with 5/16" lead anchor and screw. Wt. .68 lbs. each.
Copper strap material is 6" in length for applications where space is limited. Part is furnished with 1/2" female threads. Wt. .48 lbs. each.
Copper strap 11-3/4" in length with clamp down cable connector. Part is furnished with 1/2" female threads. Wt. .70 lbs. each.
Cast bronze part provided with 1/2" female threads and two hex-head bolts for securing cable. May be furnished with 5/8" threads when specified.
Cast bronze part has 1/2" female threads. Wt. .78 lbs. each.
Cast bronze part has 5/8" male threads. Wt. .84 lbs. each.
Aluminum Cables
Aluminum cable used as in secondary bonding requirements.
Copper conducttor cable for Class 2 installations or structures over 75′ in height.
Aluminum cable used in Class 1 structures or under 75′ in height.
28 strands x 17 gauge wire for residential applications.
Aluminum conductor cable for Class 2 installations which is structures over 75′ in height.
Conductor cable that is tinned for used in Class 1 structures that are under 75′ in height.
Conductor cable used in Class 1 structures which are buildings under 75′ in height.
Conductor cable that is tinned for use in Class 2 structures that are over 75′ in height.
Flat conductor cable used in cases where flat cable is needed. Class 1 and under 75′ in height.
Copper cable used primarily for grounding and counterpoise installations.
Copper Cables
Flexible Bonding Cables
Strip Copper & Aluminum
Aluminum Bonding Plates & Straps
Cast aluminum plate and size is 4″ x 4″ x 3/16″ affording 16 square inches of bonding area. Wt. .40 lbs. each.
Cast aluminum plate with 8 square inches of bonding area and mounting hole is 3/4″ diameter. Wt. .26 lbs. each.
Cast aluminum crimp style fitting IP-A5 with IP-A49 aluminum strap for use with bonding metal bodies up to 2″ diameter pipe standard cable. Longer lengths available upon request. Wt. .14 lbs. each.
Cast aluminum crimp style fitting IP-A4 with IP-A49 aluminum strap for use with bonding metal bodies up to 2″ diameter pipe. Longer lengths available upon request. Wt. .08 lbs. each.
Cast aluminum crimp and pressed aluminum splicer for standard cable bonds to metallic surfaces. Wt. .10 lbs. each.
Cast pressure type fitting IP-A596 with 15″ of IP-A49 aluminum strap for bonding metal bodies up to 4″ diameter pipe. Longer lengths available upon request. Wt. .30 lbs. each.
Cast aluminum crimp style fitting IP-A5 with 15" length of IP-A49 aluminum strap for bonding metal bodies up to 4" diameter pipe. Longer lengths available upon request. Wt. .20 lbs. each.
Cast aluminum plate and size is 6″ x 4 -7/16″ x 3/16″ with over 26 square inches of bonding area. Wt. 1.20 lbs. each.
Cast aluminum plate with pressure type universal style cable fastener. Bonding area is 8 square inches. Mounting holes have a 5/16″ dia. and are 3″ center to center. Wt. .22 lbs. each.
Cast aluminum connector is used with IP-A49 strap. Wt. .06 lbs. each.
Cast aluminum crimp connector for standard cable and for 1″ strap IP-A49. Wt. .14 lbs.
Aluminum Bus Terminals/Track Connectors
Cast aluminum crimp splicer connector for standard size cable. Wt. .06 lb. each.
Cast aluminum bus terminal with 6 square inches of surface contact for two cables up to 5/8″ diameter. Mounting hole is 1/2″ diameter. Wt. .46 lbs. each.
Cast aluminum crimp splicer connector for smaller cable. Mounting hole is 5/16″ diameter. Wt. .04 lbs.
Cast aluminum crimp splicer connector for standard cable. Mounting hole is 5/16″ diameter. Wt. .08 lbs. each.
Cast aluminum with 4-1/2 square inches of contact for standard cable. Mounting hole is 1/2″ diameter. Wt. .18 lbs. each
Cast aluminum has 3 square inches of surface contact for connecting larger cables to larger metal bodies. Mounting hole is 1/2″ diameter. Wt. .24 lbs. each.
Cast aluminum used for connecting standard cable. Mounting hole is 1/2″ diameter. Wt. .12 lbs. each.
Cast aluminum bonding lug for smallerbonding cable. Mounting hole is 5/16″ diameter. Wt. .06 lbs. each.
Aluminum Cross Run Clamps and Other Types
Cast aluminum pressure type connector for connecting two larger cables up to 5/8″ diameter. Wt. is .16 lbs. each.
Cast aluminum pressure type connector for standard size cable. Wt. .16 lbs. each.
Cast aluminum pressure type connector for bonding cables only. Wt. .08 lbs. each.
Cast aluminum part provides 8 square inches of bonding area. For cables as shown and for use with steel plates up to 3/4″ thick. Wt. .58 lbs. each.
Aluminum Parallel Splicers and Connectors
Cast aluminum crimp splicer 2" length. Wt. .06 lbs. each.
Cast aluminum crimp splicer 2" length. For one main cable and one bonding cable. Wt. .06 lbs. each.
Cast aluminum pressure style connector 1″ length. For one primary and one secondary cable. Wt. .14 lbs. each.
Cast aluminum pressure style connector 2-1/2″ length. Wt. .38 lbs. each.
Cast aluminum crimp splicer 3/4″ length. For one primary and one secondary cable. Wt. .08 lbs. each.
Cast aluminum pressure style connector 2″ length. Wt. .14 lbs. each.
Cast aluminum pressure type connector 4″ in length. Wt. .34 lbs. each.
Cast aluminum pressure style connector 2″ in length. Wt. .28 each.
Aluminum Straight Connectors
Cast aluminum for use with 1/2″ notched rod. Wt. .04 lbs. each.
Pressed aluminum crimp splicer 3-3/4″ length. Wt. .04 lbs. each.
Machined aluminum compression splicer 2″ length. Wt. .04 lbs. each.
Machined aluminum bolt style part 4 7/8″ length. Wt. .24 lbs. each.
Aluminum T Splicers
Cast bronze part for use with plain 3/8″ threaded rod and crimp type connector
for standard cable. Wt. .12 lbs. each.
Cast aluminum crimp cable connector for cable and solid number 6 electrical wire. Wt. .04 lbs. each.
Cast aluminum pressure type “T" connector. Wt. .18 lbs. each.
Cast aluminum crimp splicer. For one primary and secondary cable. Wt. .08 lbs. each.
Cast aluminum for use with 1/2″ notched rod. Wt. .18 lbs. each.
Bi-Metallic
Machined stainless steel for use with secondary cable. Length is 4″. Wt. .14 lbs. each.
Cast aluminum & bronze crimp splicer for use with copper and aluminum cable. Wt. .30 lbs. each.
Cast aluminum & bronze crimp splicer for use with copper and aluminum cable. Wt. .34 lbs. each.
Cast aluminum and bronze crimp splicer 5-1/2″ length. Wt. .36 lbs. each.
Cast bronze and aluminum pressure type “T" connector. Wt. .64 lbs. each.
Cast bronze and aluminum pressure type “T" Connector. Wt. .64 lbs. each.
Cast bronze and aluminum. For connectingn copper cable to aluminum surfaces. Mounting hole is 5/16″ diameter. Wt. .48 lbs. each.
Cast aluminum and bronze for connecting copper cable to structural beams. Part provides 8 square inches of bonding area. Mounting holes are 5/16″ diameter. Wt. .60 lbs. each.
Cast bronze and aluminum pressure style connector. Wt. .30 lbs. each.
Machined brass and aluminum part for use with copper and aluminum cables. Length is 5″. Wt. .45 lbs. each.
Copper Bonding Plates & Straps
Cast bronze plate and size is 4" x 4" x 3/16" affording 16 square inches of bonding area. Wt. 1.20 lbs. each.
Cast bronze plate and size is 6" x 4 –7/16" x 3/16" with over 26 square inches of bonding area. Wt. 3.40 lbs. each.
Cast bronze crimp style fitting IP-5 with 15" length of tinned IP-49X copper strap for bonding metal bodies up to 4" diameter pipe. Longer lengths available upon request. Wt. .42 lbs. each.
Cast pressure type fitting IP-596 with 15" of tinned IP-49X copper strap for bonding metal bodies up to 4" diameter pipe. Longer lengths available upon request. Wt. .80 lbs.
Crimp fitting with IP-49Y bonding strap for pipes up to 1-1/2" diameter. Part is tinned. Wt. .42 lbs. each.
Cast bronze crimp and pressed copper splicer for standard cable bonds to metallic surfaces. Part is tinned. Wt. .22 lbs. each.
For use with IP-12 for pipes up to 3" diameter. Part is tinned. Wt. .26 lbs. each.
Cast bronze crimp style fitting IP-4 with IP-49 copper strap for use with bonding metal bodies up to 2" diameter pipe. Longer lengths available upon request. Wt. .22 lbs. each.
Cast bronze crimp style fitting IP-5 with IP-49 copper strap for use with bonding metal bodies up to 2" diameter pipe. Longer lengths available upon request. Wt. .28 lbs. each.
Cast bronze plate with 8 square inches of bonding area and mounting hole is 3/4" diameter. Wt. .78 lbs. each.
Cast bronze plate with pressure type universal style cable fastener. Bonding area is 8 square inches. Mounting holes have a 5/16" dia. and are 3" center to center. Wt. .66 lbs. each.
Cast bronze connector is used with IP-49 strap. Wt. .14 lbs. each.
Cast bronze crimp connector for standard cable and for 1" strap IP-49. Wt. .28 lbs. each.
Copper Bus Terminals/Track Connectors
Cast bronze crimp splicer connector for standard size cable. Wt. .18 lb. each.
Cast bronze bus terminal with 6 square inches of surface contact for two cables up to 5/8" diameter. Mounting hole is 1/2" diameter. Wt. 1.12 lbs. each.
Cast bronze crimp splicer connector for smaller cable. Mounting hole is 5/16" diameter. Wt. .08 lbs. each.
Cast bronze crimp splicer connector for standard cable. Mounting hole is 5/16" diameter. Wt. .14 lbs. each.
Cast bronze with 4-1/2 square inches of contact for standard cable. Mounting hole is 1/2" diameter. Wt. .54 lbs. each.
Cast bronze has 3 square inches of surface contact for connecting larger cables to larger metal bodies. Mounting hole is 1/2" diameter. Wt. .68 lbs. each.
Cast bronze used for connecting standard cable. Mounting hole is 1/2" diameter. Wt. .28 lbs. each.
Cast bronze bonding lug for smaller bonding cable. Mounting hole is 5/16" diameter. Wt. .14 lbs. each.
Copper Cross Run Clamps and Other Types
Cast bronze pressure type connector for connecting two cables. Wt. .58 lbs. each.
Cast bronze pressure type connector for connecting two larger cables up to 5/8" diameter. Wt. is .46 lbs. each.
Cast bronze part provides 8 square inches of bonding area. For cables as shown and for use with steel plates up to 3/4" thick. Wt. 1.58 lbs. each.
Cast bronze connector for use with 3/8" rod and 1" flat strip. Wt. .12 lbs. each.
Cast bronze pressure type connector for bonding cables only. Wt. .18 lbs. each.
Cast bronze pressure type connector for standard size cable. Wt. .40 lbs. each.
Cast bronze cable connector for solid number 6 electrical wire for bonding to flat metal surface. Wt. .14 lbs. each.
Copper Parallel Splicers and Connectors
Cast bronze crimp splicer 2" length. For one main cable and one bonding cable. Wt. .08 lbs. each.
Cast bronze crimp splicer 2" length. For use with two bonding cables. Wt. .10 lbs. each.
Cast bronze pressure style connector 1" length. For one primary and one secondary cable. Wt. .28 lbs. each.
Cast bronze pressure style connector 2-1/2" length. Wt. .80 lbs. each.
Cast bronze crimp splicer 3/4" length. For one primary and one secondary cable. Wt. .22 lbs. each.
Cast bronze pressure style connector 2" length. Wt. .38 lbs. each.
Cast bronze pressure type connector 4" in length. Wt. .86 lbs. each.
Cast bronze pressure style connector 2" in length. Wt. .54 each.
Copper Straight Connectors
Cast bronze for use with 3/8" notched rod. Part is tinned. Wt. .10 lbs. each.
Pressed copper crimp splicer 3-3/4" length. Wt. .10 lbs. each.
Machined brass compression splicer 2" length. Wt. .10 lbs. each.
Machined brass bolt style part 4 7/8" length. Wt. .65 lbs. each.
Copper T Splicers
Cast bronze for use with 3/8" notched rod. Part is tinned. Wt. .34 lbs. each.
Cast bronze part for use with plain 3/8" rod and crimp type connector for standard cable. Wt. .12 lbs. each.
Cast bronze crimp splicer. For one primary and secondary cable. Wt. .10 lbs. each.
Cast bronze pressure type “T" connector. Wt. .52 lbs. each.
Cast crimp cable connector for cable and solid number 6 electrical wire. Wt. .14 lbs. each.
Fasteners
Pressed copper adhesive cable holder with three fold-over tabs to secure cable. Fastener has rolled edges to prevent cuts to mounting surfaces. For use on flat surfaces where fastener penetration is not an option. Size is 2-1/2" wide x 3-1/2" length. Wt. .08 lbs. each
Superior polycarbonate plastic adhesive cable holder. Part is 2-3/8" wide x 3-1/4" long. Part is extremely durable and is fully tested and approved by UL including temperature and impact tests. Wt. .04 lbs. each.
Cast bronze with clamp style fastener is 3" in diameter. Wt. .32 lbs. each.
Superior polycarbonate plastic adhesive cable holder. Part is 2-3/8" wide x 3-1/4" long. Part is extremely durable and has been fully tested and approved by UL including temperature and impact tests. Smooth ID for use with larger cables. Wt. .04 lbs. each.
Pressed aluminum adhesive cable holder with three fold-over tabs to secure cable. Fastener has rolled edges to prevent cuts to mounting surfaces. For use on flat surfaces where fastener penetration is not an option. Size is 2-1/2″ wide x3-1/2″ length. Wt. .04 lbs. each. Scott Test
Cast aluminum with clamp style fastener is 3" in diameter. Wt. .10 lbs. each.
Cast bronze fastener with IP-295 lead anchor and IP-132L (1/4" x 1")screw. Wt. .08 lbs. each.
Assembly includes copper loop fastener and a 1/4" expansion anchor. Wt. .08 lbs. each.
Cast bronze clamp with IP-294A expansion anchor and 5/16" x 1-1/2" screw. Wt. .08 lbs. each.
Assembly includes a copper loop fastener and a 1/4" lead anchor. Wt. .08 lbs. each.
Assembly includes 1" SS wood screw, a copper loop fastener, and lead anchor. Wt. .046 lbs. each.
Assembly includes an aluminum loop Fastener and a 1/4" expansion anchor. Wt. .05 lbs. each.
Stainless steel drive nail anchor, 1/4" diameter x 1-1/4" length. Wt. .02 lbs. each.
Cast aluminum fastener with IP-295 lead anchor and IP-132L (1/4" x 1") screw. Wt. .06 lbs. each.
5/16"-18, 1-1/2" length. Drill size 9/16". Wt. .04 lbs. each.
Cast aluminum clamp with IP-294A expansion anchor and 5/16" x 1-1/2" screw. Wt. .06 lbs. each.
Assembly includes an aluminum loop Fastener and a 1/4" expansion anchor. Wt. .05 lbs. each.
5/16"-18, 1-1/2" length. Drill size 9/16". Wt. .04 lbs. each.
1/2"-13, 1-1/2" length. Drill size 7/8". Wt. .16 lbs. each.
3/8"-16, 1-1/4" length. Drill size 3/4". Wt. .10 lbs. each
For #12 Size Screw (IP-225), 1-1/2" length. Drill size 5/16". Wt. .02 lbs. each.
For #12 Size Screw (IP-224), 1" length. Drill size 5/16". Wt. .02 lbs. each.
5/16"-18, 1" length. Drill size 5/8". Wt. .06 lbs. each.
1/4"-20, 3/4" length. Drill size 1/2". Wt. .04 lbs. each.
1/4"-20, 1-1/4" length. Drill size 1/2". Wt. .02 lbs. each.
Assembly includes 1" SS wood screw, a aluminum loop fastener, and lead anchor. Wt. .036 lbs. each.
Assembly includes an aluminum loop fastener and a 1/4" lead anchor. Wt. .07 lbs. each.
Bolts, Nails, Screws, Nuts
#12 – 3/4" length – Stainless Steel. Wt. .006 lbs. each.
#10-14 x 1" length Self-tapping Stainless Steel. Wt. .007 lbs. each.
#12-14 x 1-1/4" length Self-tapping Stainless Steel. Wt. .011 lbs. each.
1/4" -20 x 1/2" length. Stainless Steel. Wt. .010 lbs. each.
Pressed copper loop for standard size cables. Mounting hole is 1/4" diameter. Wt. .02 lbs. each.
Pressed copper loop for 4/0 cable. Mounting hole is 1/4" diameter. Wt. .04 lbs. each.
Pressed copper loop for standard size cables. Wt. .01 lbs. each.
Pressed aluminum loop for standard size cables. Mounting hole is 1/4" diameter. Wt. .01 lbs. each.
Pressed aluminum loop for 4/0 cable. Mounting hole is 1/4" diameter. Wt. .01 lbs. each.
Pressed aluminum loop for standard size cables. Wt. .006 lbs. each.
Cast bronze fastener has 1/4" diameter mounting hole. Wt. .04 lbs. each.
Cast bronze fastener for mounting with nail. Wt. .04 lbs. each.
Pressed copper fastener clamp is for installation onto slate roofs for cable that runs parallel or perpendicular. Length is adjustable, slips under shingle and hooks around nail. Wt. .15 lbs. each.
Cast bronze base with loop style fastener for seams up to 13/16" wide. Cable run can be parallel or perpendicular. Wt. .18 lbs. each.
Pressed copper fastener clamp will fit railings up to 1-3/4" diameter. Larger diameters available upon request. Wt. .12 lbs. each.
Cast bronze fastener with crimp type connector. Base is filled with stone or chips and adhered to roof with adhesive. Outer diameter is 4" with inside diameter at 3-1/2". Wt. .98 lbs. each.
Pressed aluminum fastener clamp will fit railings up to 1-3/4" diameter. Larger diameters available upon request. Wt. .06 lbs. each.
Cast aluminum fastener with crimp type connector. Base is filled with stone or chips and adhered to roof with adhesive. Outer diameter is 4" with inside diameter at 3-1/2". Wt. .30 lbs. each.
Pressed aluminum fastener clamp is for installation onto slate roofs for cable that runs parallel or perpendicular. Length is adjustable, slips under shingle and hooks around nail. Wt. .06 lbs. each.
Cast aluminum fastener has 1/4" diameter mounting hole. Wt. .01 lbs. each.
Washers and Seals
Washer for use with nails or screws. Wt. .014 lbs. each.
Washer for use with either 3/8" or 1/2" stems. Wt. .062 lbs. each.
Grounding Equipment
Cast bronze part has four hex screws and is used for cross-connecting 1/2" diameter cable to either 5/8" or 3/4" diameter ground rods. Wt. .64 lbs. each.
Made from 20 gauge copper sheet with each wing 3-1/2" wide x 18" length. Wt. 3.46 lbs. each.
Made from 20 gauge copper sheet with each wing 6" wide x 9" length. Wt. 2.66 lbs. each.
Ground plate is cast from bronze and is 12" x 12" x 1/4" thick with two mechanical cable clamps to secure the cable. Wt. 13.28 lbs. each.
Ground plate is cast from bronze and is 12" x 12" x 1/2" thick with two mechanical cable clamps to secure the cable. Wt. 20.68 lbs. each.
Ground plate is made from 20 gauge copper sheets and is 18" x 36" with two mechanical cable clamps to secure the cable. Wt. 6.75 lbs. each.
Ground plate is made from 20 gauge copper sheets. Sheet is 36" x 36" and has two mechanical cable clamps to secure the cable. Wt. 13.48 lbs. each.
Ground plate is made from 20 gauge copper sheets and is 18" x 24" with two mechanical cable clamps to secure the cable. Wt. 4.60 lbs. each.
Ground plate is made from 20 gauge copper sheets and is 18" x 18" with two mechanical cable clamps to secure the cable. Wt. 3.13 lbs. each.
Copperclad steel ground rods. 1/2" diameter 8' long Wt: 5.52 lbs each.
Copperclad steel ground rods. 1/2" diameter 10' long Wt. 6.98 lbs. each.
Copperclad steel ground rods. 5/8" diameter 8' long Wt: 6.68 lbs each.
Cast bronze 1/2" Clamp for securing cable to ground rod. Wt. .36 lbs. each.
Cast bronze 3/4" Clamp for securing cable to ground rod. Wt. .52 lbs. each.
Copperclad steel ground rods. 5/8" diameter 10' longWt: 8.44 lbs each.
Copperclad steel ground rods. 3/4" Diameter 10' long Wt. 12.36 lbs. each.
Galvanized steel fastener for use with IP-349 polyurethane “U" guard or 3/4" PVC. Not for use with copper guards. Wt. .08 lbs. each.
Preformed polyurethane “U" guard is 8' in length and may be painted to desired color. For cables through 2/0 size. Wt. .68 lbs. each.
Copper guard pipe is 8' in length and 3/4" diameter. Fits standard cables through 2/0. Wt. 4.26 lbs. each.
Cast bronze guard fastener for use with IP-591, 3/4" copper guard pipe. Bolt hole size is 5/16" diameter. Wt. .06 lbs. each.
Cast bronze wedge is used when coursing cable through 1" diameter copper conduit. Wedges must be used to bond cable on each end of conduit. Wt. .26 lbs. each.
Cast bronze wedge is used when coursing cable through 3/4" diameter copper conduit. Wedges must be used to bond cable on each end of conduit. Wt. .04 lbs. each.
Cast bronze part with 4" length cable connector for connection to 5/8" diameter ground rod. Part also available for 3/4" diameter ground rod upon request. Wt. .86 lbs. each.
Cast bronze connector for ground rods up through 3/4" diameter and for connection to one cable in either a vertical or horizontal position. Wt. .60 lbs. each.
Cast bronze connector used in addition to ground rod clamp where a connection is needed to tap into a counterpoise or ground loop. One or two horizontal cables can be utilized and ground rod up to 3/4" diameter. The 28U U-bolt clamp is not to be used as a primary ground connection but rather for a secondary connection to a supplemental grounding system. Wt. .62 lbs. each.
Cast bronze receptacle with cable clamp and fastener for connecting one or two cables to ground rod. Lid is furnished with SS chain that secures top to receptacle. When ordering, specify ground rod diameter and threaded or plain ground rod. Wt. 2.72 lbs. each.
Cast bronze receptacle for use with ground rod. Lid is furnished with SS chain that secures top to receptacle. When ordering, specify ground rod diameter and threaded or plain ground rod. Wt. 2.22 lbs. each.
Made of 20 gauge copper sheet, canister is 4" in diameter and 24" length filled with charcoal. Wt. 6.8 lbs. each.
Made of 20 gauge copper sheet, perforated canister is 4" in diameter & 24" in length and filled with charcoal. Wt. 6.8 lbs. each.
Cast aluminum wedge is used when coursing cable through 1" diameter aluminum conduit. Wedges must be used to bond cable on each end of conduit. Wt. .08 lbs. each.
Cast bronze clamp and 12" Tite-Grip copper strap for bonding to pipes up to 2" diameter. Strap (IP49Y) is shaped around pipe. Casting is positioned within 1/8" of pipe and screw is tightened on flat part of casting. Screws on beveled edge are tightened to draw strap tight. Other length straps available upon request. Wt. 1.02 lbs. each
Cast bronze clamp and 18" Tite-Grip copper strap for bonding to pipes up to 4" diameter. Strap (IP-49Y) is shaped around pipe. Casting is positioned within 1/8" of pipe and screw is tightened on flat part of casting. Screws on beveled edge are tightened to draw strap tight. Other length straps available upon request. Wt. 1.21 lbs. each.
Cast bronze clamp and 32" Tite-Grip copper strap for bonding to pipes up to 8" diameter. Strap (IP-49Y) is shaped around pipe. Casting is positioned within 1/8" of pipe and screw is tightened on flat part of casting. Screws on beveled edge are tightened to draw strap tight. Other length straps available upon request. Wt. 1.70 lbs. each.
Cast bronze pipe clamp for cables through 2/0 providing 1-1/2" contact. Fits 1/2" — 1" iron pipes and 1/4" — 1" copper pipes. Maximum 1-1/2" outer diameter. Part is tinned to prevent corrosion. Wt. .48 lbs. each.
Cast bronze pipe clamp for cables through 2/0 providing 1-1/2" contact. Fits 1-1/2" — 2" iron pipes. Maximum 2-1/4" outer diameter. Lower casting may be inverted to fit smaller diameter pipes. Lower casting is tinned to prevent corrosion. Wt. 1.04 lbs. each.
Cast bronze pipe clamp for cables through 2/0 providing 1-1/2" contact. Fits 2-1/2" — 4" iron pipes. Maximum 4-1/2" outer diameter. Lower casting is tinned to prevent corrosion. Wt. 2.44 lbs. each.
Cast bronze pipe clamp for cables through 2/0 providing 1- 1/2"contact. Fits maximum 3/4" copper pipe and by inverting bottom casting allows for smaller 1/4"— 5/8" copper pipe. Lower casting is tinned to prevent corrosion. Wt. .62 lbs. each.
Cast bronze pipe clamp for cables through 2/0 providing 1-1/2" contact. Fits 1-1/4" and 1-1/2" iron pipes. Maximum 2" outer diameter. Part is tinned to prevent corrosion. Wt. .48 lbs. each.
Cast aluminum pipe clamp for cables through 2/0 providing 1-1/2" contact. Fits 1/2" — 1" iron pipes and 1/4" — 1" aluminum pipes. Maximum 1-1/2" outer diameter. Wt. .48 lbs. each.
Cast aluminum cable clamp for cables through 4/0 providing 1-1/2" contact. Fits 1-1/2" — 2" iron pipes. Maximum 2-1/4" outer diameter. Lower casting may be inverted to fit smaller diameter pipes. Lower casting is tinned bronze to prevent corrosion. Wt. .80 lbs. each.
Cast aluminum pipe clamp for cables through 2/0 providing 1-1/2" contact. Fits 2-1/2" - 4" iron pipes. Maximum 4-1/2" outer diameter. Lower casting is tinned bronze to prevent corrosion. Wt. 2.14 lbs. each.
Cast aluminum pipe clamp for cables through 2/0 providing 1-1/2"contact. Fits maximum 3/4" aluminum pipe and by inverting bottom casting allows for smaller 1/4"— 5/8" aluminum pipe. Wt. .40 lbs. each.
Cast aluminum pipe clamp for cables through 2/0 providing 1-1/2" contact. Fits 1-1/4" and 1-1/2" iron pipes. Maximum 2" outer diameter. Wt. .26 lbs. each.
Thru-Roof & Thru-Wall Assemblies & Components
240 Connector is used as the cable connector when used as a thru-roof assembly.
240 Nail Bracket is used as the mounting support when component is used in a thru-roof assembly.
240 Stem Series – Specify for 3/8″ or 1/2″ and overall length. Solid copper rod with 2″ of threads on one end of rod. Stem is for use in thru-roof assembly.
Part 334T is 3/8″ stainless steel thread rod with length to be specified.
Part 334T is 1/2″ stainless steel thread rod with length to be specified.
A240 Connector is used as the cable connector when used in a thru-roof assembly.
240 aluminum nail bracket is used as the mounting support when component is used in a thru-roof assembly.
A240 Stem Series – 1/2″ aluminum rod with 2″ of threads on one end of rod. Length to be specified. Stem for use in thru-roof assembly.
Machined brass connector with hex-head bolts. Wt. .26 lbs. each.
Machined bronze connector with set screws. Wt. .26 lbs. each.
Machined aluminum connector with hex-head bolts. Wt. .08 lbs. each.
Machined aluminum connector with set screws. Wt. .08 lbs. each.
Assembly includes 3/8"x 15" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.02 lbs. each.
Assembly includes 3/8"x 24" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.31 lbs. each.
Assembly includes 3/8"x 18" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.16 lbs. each.
Assembly includes 1/2"x 18" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.36 lbs. each.
Assembly includes 1/2"x 15" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.14 lbs. each.
Cast bronze with swivel crimp connector on each end with threaded stainless steel rod 3/8" x 4-3/4". Wt. .76 lb. each. 22 28S 32S 40 21 G3 A22 A28 A30
Cast bronze connector with pressure style cable fastener on top and crimp connector on bottom side. Bottom side of part is recessed to allow for sealant to assure a weather tight seal. Wt. .72 lbs.
Machined brass and cast aluminum assembly consists of aluminum IP-A597 cap, cable connector on top, IP-M597C brass bottom cable connector with set screws and 1/2" x 8" threaded stainless steel rod. Wt. .80 lbs. each. The PVC conduit and boot flashing are shown for illustrative purposes only and are not supplied by IPC as part of the assembly. Longer lengths of threaded rod are available upon request..
Cast bronze, machined brass and cast aluminum assembly consists of aluminum IP-A597 cap, cable connector on top, bronze IP-179A base plate, brass IP-M597C bottom cable connector with set screws and 1/2" x 8" threaded stainless steel rod. Wt. 1.30 lbs. each. The PVC conduit and boot flashing are shown for illustrative purposes only and are not supplied by IPC as part of the assembly. Longer lengths of threaded rod are available upon request..
Cast bronze and machined brass assembly consists of IP-597 cap, cable connector, IP-179A base plate, IP-M597C bottom cable connector with set screws and 1/2" x 8" threaded stainless steel rod. Wt. 1.60 lbs. each. The PVC conduit and boot flashing are shown for illustrative purposes only and are not supplied by IPC as part of the assembly. Longer lengths of threaded rod are available upon request.
Assembly includes 3/8"x 15" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.02 lbs. each.
Cast bronze, machined brass and cast aluminum assembly consists of aluminum IP-A597 cap, cable connector on top, bronze IP-179A base plate, brass IP-M597C bottom cable connector with set screws and 1/2" x 8" threaded stainless steel rod. Wt. 1.30 lbs. each. The PVC conduit and boot flashing are shown for illustrative purposes only and are not supplied by IPC as part of the assembly. Longer lengths of threaded rod are available upon request.
Machined brass and cast aluminum assembly consists of aluminum IP-A597 cap, cable connector on top, IP-M597C brass bottom cable connector with set screws and 1/2″ x 8″ threaded stainless steel rod. Wt. .80 lbs. each. The PVC conduit and boot flashing are shown for illustrative purposes only and are not supplied by IPC as part of the assembly. Longer lengths of threaded rod are available upon request.
Cast bronze connector with pressure style cable fastener on top and crimp connector on bottom side. Bottom side of part is recessed to allow for sealant to assure a weather tight seal. Wt. .72 lbs.
Cast bronze with swivel crimp connector on each end with threaded stainless steel rod 3/8" x 4-3/4". Wt. .76 lb. each. 22 28S 32S 40 21 G3 A22 A28 A30
Assembly includes 1/2"x 15" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.14 lbs. each.
Assembly includes 1/2"x 18" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.36 lbs. each.
Assembly includes 3/8"x 18" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.16 lbs. each.
Assembly includes 3/8"x 24" copper stem threaded 2 inches, neoprene washer (247A), nailing bracket and cable connector. Wt. 1.31 lbs. each.
Assembly includes two cable connectors in bronze and aluminum, 1/2" x 12" stainless steel threaded rod, Neoprene® washer, hex nut and washer. Longer lengths of thread rod available upon request. Wt. 1.20 lbs. each.
Thru wall assembly consists of two Neoprene® washers, hex nut, washer, M597 cable connector on each end and 1/2" x 8" threaded stainless steel rod. Wt. 1.10 lbs. each.
Cast aluminum assembly includes two aluminum cable connectors, 1/2" x 12" stainless steel threaded rod, Neoprene® washer, hex nut and washer. Longer lengths of threaded rod available upon request. Wt. .60 lbs. each.
Thru wall assembly consists of two Neoprene® washers, hex nut, washer, MA597 cable connector on each end and 1/2″ x 8″ threaded stainless steel rod. Wt. .68 lbs. each.
Cast bronze assembly includes two bronze cable connectors, 1/2" x 12" stainless steel threaded rod, Neoprene® washer, hex nut and washer. Longer lengths of thread rod available upon request. Wt. 1.78 lbs. each.
Strike Termination
For use with 3/8" notched rod. Strike termination device has set screw and approximately 4-3/4" in length. Wt. .06 lbs. each.
For use with 3/8" rod and standard or round tile up to 7/8" thick. Wt. .18 lbs. each.
For use with 3/8" rod and standard or round tile up to 1-3/8" thick. Wt. .22 lbs. each.
For use with 1/2" notched rod. Strike termination device is 8" in length and slips onto notched rod. Wt. .06 lbs. each.
For use with 1/2" rod and standard or round tile up to 1-3/8" thick. Wt. .08 lbs. each.
Tin Coated Solid Copper Chimney Notched Rod
Solid Aluminum Chimney Notched Rod
1-1/8" diameter Neoprene® ball to fit on sharp tip strike devices. Secure with silicone or construction adhesive to prevent removal of protector. Wt. .03 lbs. ea
Cast solid bronze decorative terminal. Part is nickel plated and is 11 5/8" in length. Part has 3/8" female threads. Wt. .54 lbs. each.
Cast solid bronze decorative terminal. Part is plain finish and 11 5/8" in length. Part has 3/8" female threads. Wt. .54 lbs. each.
Cast solid bronze decorative terminal. Part is nickel plated and is 11 5/8" in length. Part has 1/2" female threads. Wt. .54 lbs. each.
Cast solid aluminum decorative terminal. Part is 11 5/8" long. Part has 1/2" female threads. Wt. .16 lbs. each.
Assembly consists of 1/2" x 12" length solid copper blunt tip air terminal mounted on a 6" stainless steel spring assembly. Total overall length is 18". Wt. 1.28 lbs. each.
Assembly consists of 1/2" x 12" length solid aluminum blunt tip air terminal mounted on a 6" stainless steel spring assembly. Total overall length is 18". Wt. .60 lbs. each.
Pressed copper coupler is crimped into tube point prior to shipping. Wt. .12 lbs. each.
Pressed aluminum coupler is crimped into tube point prior to shipping. Wt. .04 lbs. each.
Machined solid brass coupler with 5/8" female threads is crimped to tube point prior to shipping. Wt. .18 lbs. each.
Machined solid brass coupler with 1/2" male threads is crimped to tube point prior to shipping. Wt. .16 lbs. each.
Machined solid aluminum coupler with 5/8" female threads is crimped to tube point prior to shipping. Wt. .06 lbs. each.
Machined solid aluminum coupler with 1/2" male threads is crimped to tube point prior to shipping. Wt. .04 lbs. each.
Tube points are hollow tubes used as air terminals and normally supported with tripods.